Messages

111

General Mach Discussion / Problem with outputs

« on: February 14, 2009, 11:24:12 AM »

Hello,

I have a problem with the output 2 . I have a the output# 1 enabled , port# set to 1 and pin Number set to 1 too, the spindle work well.

But the output# 2 enabled , port# set to 1 and pin Number set to 14 ,nothing works..all is wired as in the output # 1, nothing changes but it does not work..
I use breakout board campbell.. and I use the same relay , but only one that works...

Did I  do something wrong? I have tried to do the same with output#3, but I had the same result...


Could I have your help?
thanks in advance
Robhi

112

General Mach Discussion / Re: SoundLogic XML does not work

« on: February 09, 2009, 04:30:02 PM »

Hi ,

Thanks for all of you, thanks to Hood too.
Problem is solved.. I have not had the right file of Soundlogic XML.

Thanks
Robhi

113

General Mach Discussion / Re: SoundLogic XML does not work

« on: February 08, 2009, 05:00:16 PM »

Hi Hood,
Thanks a lot, I have downloaded it as you said, it is OK, it shows everythong.
i will try it tomorrow to see that my home switches do work..
thanks a lot

Robhi

114

General Mach Discussion / Re: SoundLogic XML does not work

« on: February 08, 2009, 03:33:31 PM »

Hi,
Thanks for replaying,

that is what I exactly did. I put the Sound LogicXML file in mach3 folder, and chose it when opening mach3. but , once mach3 is open, all the values are 0, even motors are not checked. nothing checked.

i would like to do so, in order to set my home switches. I have home switches, normally closed, but when they are opened, nothing happend, there is no notice that they are touched, mach3 goes on ..etc..I dona know why..
Any help please?
thanks in advance
Robhi

115

General Mach Discussion / SoundLogic XML does not work

« on: February 08, 2009, 12:26:07 PM »

HI every body,

I have a problem when the first time I tried to use the Sound LogicXML folder with Mach3.

I Would like to use it in order to set the values of the homes switches. I guess they are not easy to do them.

When I use the Sound Loginc XML in Mach3 all the parameters (values) are set to 0.
Do I did something wrong?
Thanks in advance for your suggestions
Robhi

116

General Mach Discussion / Re: Gecko 201 Disable?

« on: January 01, 2009, 03:56:53 PM »

Hi Hood and all,

Thanks too much for your answer I appreciate that.
Robhi

117

General Mach Discussion / Gecko 201 Disable?

« on: January 01, 2009, 01:52:50 PM »

Hi everybody,

happy new year to all of you.

I would like to know the function of disable in Gecko 201, Could I leave it alone and not connect it to any other wire?
What it is the advantage if I connect it (use it) and how could I use it?

thanks you and happy new year again.

Robhi

118

General Mach Discussion / Re: Wiring motors

« on: July 31, 2008, 06:33:17 PM »

OK ... I am going to do so, hoping it will work.. if not never mind..

thank you again , have a nice night

Robhi

119

General Mach Discussion / Re: Wiring motors

« on: July 31, 2008, 06:25:25 PM »

Thank you ,

I am from palestine, but I live in Switzerland since long time.

thank you again Hood
Robhi

120

General Mach Discussion / Re: Wiring motors

« on: July 31, 2008, 06:07:23 PM »

So I need 3 drives for my 3 motors.. is OK..

these 3 drives will be connected to gother ? is there any site which illustrate , explain how I can do that?
Sorry I may make you laughing.. but never mind

Robhi