Topics

21

General Mach Discussion / power supply

« on: July 10, 2008, 03:41:45 AM »

Hello,

I would like to know if I could use a power supply of 24 volt,  15 ampère for XS-3525/8S-4 of XYLOTEX.. I do not know whether it is dangers or not..

thanks in advance for your help

Robhi

22

General Mach Discussion / Help about "24VDC/5.0A "

« on: December 15, 2007, 06:55:19 AM »

hello,

Could I use a PS that is used for a printer for my:--

The XS-3525/8S-4 Stepper Motor Driver Board
The Perfect Choice For Your Sherline or Taig Four Axis CNC Retrofit

Four axis bipolar drive
±2.5 Amp/Phase PWM controlled drives
up to 35 Volt (w/BEMF)
FULL, HALF, QUARTER, & EIGHTH step/Full Step .

The PS that I would like to use is input 220 volte, output is 24VDC/5.0A .

I do not know if that would work.

any help of you will be appreciated.
thanks

Robhi

23

General Mach Discussion / help with "This is then Winding One"

« on: December 13, 2007, 10:40:27 AM »

Hi, could you help me to understand what these code mean please?

For BIPOLAR PARALLEL:
Join RED to BLUE
Join YELLOW to BLACK. This is then Winding One.
Join WHITE to BROWN
Join PURPLE to GREEN. This is then Winding Two

does it mean the following or not?

Join RED to BLUE for A
Join YELLOW to BLACK. This is then Winding One. for A#
Join WHITE to BROWN for B
Join PURPLE to GREEN. This is then Winding Two for B#

thanks for your help

24

General Mach Discussion / About Nema motors or other type

« on: December 06, 2007, 08:12:49 AM »

hello,

I do not know if i can ask some information here or not, at any rate am sorry if I can not.

what I like to know, Please, that I have the following drive:-


The XS-3525/8S-4 Stepper Motor Driver Board (Ver 4.00) $175.00

The Perfect Choice For Your Sherline or Taig Four Axis CNC Retrofit

Four axis bipolar drive
±2.5 Amp/Phase PWM controlled drives
up to 35 Volt (w/BEMF)
FULL, HALF, QUARTER, & EIGHTH step/Full Step
Built-in DC-DC Converter for 5 Volt Logic
Filtered and Buffered STEP & DIR Signals
Built-in Break-out:Screw Terminals for Unused Parallel Port I/O
Synchronous Rectification
Internal UVLO and Thermal Shutdown circuitry
Easy connect for most popular Step/Direction control software
Small Size: 5.65" X 2.85"
I would like to to have this type of motors. is it OK? Could they be used with such type of drive? Or I will have prob with?
thanks in advace for your answers

 220Ncm - 10mm Shaft - Hybrid Stepper Motor

 
SPECIAL OFFER at only £22.95!!!!
Normally £39.50

VAT Included, P&P £3.95

Arc Code AC571157525M
Type Hybrid Stepper
Holding Torque 220Ncm
Step Angle 1.8°
Rated Voltage 7.5V
Rated Current 2.5A/Phase
No. of Wires 8
Size 57x57x115mm
Shaft Dia. 10mm
Shaft Length (Front) 30mm
Shaft Length (Rear) 30mm
Net Weight 1.74kg

Robhi
 

25

General Mach Discussion / could I use more than 500 lines ?

« on: November 25, 2007, 10:17:26 AM »

hello,
as u see i am a new settler here, i wanna use mach3 , the prob that i have is that i can not use more than 500 lines in one programme..
is there any solution?
thank in advance