Messages

1

General Mach Discussion / Re: Problem with R3.043.000

« on: January 18, 2009, 02:53:07 AM »

Back to the previous version, everything works fine so there is a problem with R3.043.000

2

General Mach Discussion / Re: Problem with R3.043.000

« on: January 15, 2009, 11:58:04 PM »

Yes I just got the same problem so i am going to go back to the previous version to see if that fix the problem I will let you know

3

General Mach Discussion / Re: Set up Mach3 software for my CNC machine

« on: March 25, 2008, 08:01:21 PM »

Jeffmorris
Here is a link for a PDF document who can help a lot
http://www.machsupport.com/documentation/Mach3%20Setup%20Tutorial.pdf

Bruno

4

General Mach Discussion / Re: Mach3 "cuts corners" toolpath not respected

« on: March 14, 2008, 12:19:48 AM »

Issue resolved with this document who really help me. I did not know it's existence as it was recently added> Now I can understand the implications of the acceleration.
Thank to everyone.
Bruno

5

General Mach Discussion / Re: Mach3 "cuts corners" toolpath not respected

« on: March 13, 2008, 04:24:12 PM »

Hi Whacko
I got a blank page on page 5.24

6

General Mach Discussion / Re: Mach3 "cuts corners" toolpath not respected

« on: March 13, 2008, 04:13:12 PM »

Hi Chip,
Well if I do that 1/ I got an abnormal condition 2/ the movement of X and Y is extremely choppy.
Bruno

7

General Mach Discussion / Mach3 "cuts corners" toolpath not respected

« on: March 13, 2008, 01:33:48 PM »

I have a solsylva machine that I highly upgraded so I can cut up to 170 IPM and travel at 225 IPM.
I am having a little problem: If I cut at 100IPM everything is fine and all dimensions are respected.
At 150 IPM the toolpath is no longer respected and mach3 seems to "cut the corners". For example
if you cut a square  mach will round the path on corners.
Is anyone can help me  understand?
Bruno

8

General Mach Discussion / Re: MACH3 is starting the router on its own... Scarry!!!!

« on: March 09, 2008, 05:01:22 AM »

Good news again
I find out that if you uninstall all the printer drivers and you disable the ECP printer it stays disable after reboot so I am now sure that the ECP was the problem so far my machine is on for now 4 hours and the spindle stays off. The trick was to get rid of the drivers of any printer.
Bruno

9

General Mach Discussion / Re: MACH3 is starting the router on its own... Scarry!!!!

« on: March 07, 2008, 04:56:38 PM »

I think we are not done yet:
I uninstalled this EPC printer, shut down the computer, reboot and guess what the EPC driver is back and enable again and after 3 min the spindle start on its own again....scary!!!!

So how I can get make this driver disappearing, I tried to uninstalled it 3 time and every time it is back.
Bruno

10

General Mach Discussion / Re: MACH3 is starting the router on its own... Scarry!!!!

« on: March 07, 2008, 12:14:49 PM »

This time we got the complete answer.
After 45min the spindle was still behaving well and was still off so I decided to out the entire system back to what it was pin#1 and this ECP driver enable. Guess what happens... I was back to the same problem , after less than 3min the router started on its own....Scary!!!
This time I really feel that you guy found the solution.
My ten fingers thanks you very much, and I am sure this thread will serve other people as well.
Thank you again,
Bruno