Messages

361

dspMC/IP Motion Controller / Re: Analog inputs.

« on: February 09, 2009, 11:30:55 AM »

the analog input data is stored in oem dros in mach.  what hardware model do you have 7761 or 7761-Sx or 7761-Mx.

362

dspMC/IP Motion Controller / Re: Using dspMC and PPort together?

« on: February 04, 2009, 02:19:42 PM »

The I/O is all controlled by Mach3.  so if we allow access to PPort, it will just go to Mach3, not the DSPMC.  Only the I/O mapped to the DSPMC will go over ethernet.

the only problem I see right now is that the pport input scanning will be slow so you wont be able to use the inputs for a fast mpg.  regular on/off will be ok.


thanks
Rufi

363

dspMC/IP Motion Controller / Re: Using dspMC and PPort together?

« on: February 02, 2009, 05:27:21 PM »

ok.  when you do order more units, we will schedule time for it. 

I think we can scan the pport atmost 1khz from within the plugin.

Rufi

364

dspMC/IP Motion Controller / Re: Using dspMC and PPort together?

« on: February 02, 2009, 01:47:37 PM »

ger21 is right.  Mach does not read/write the parallel port when external movement plugin is selected.  The plugin has to support it.  Currently the plugin open the link to dspmc over ethernet and does not touch the parallel port.  If we get some time, we can look into using parallel port for I/O as well.  So far there is not much demand of more I/O than what is on the dspmc board.

regards
Rufi

365

dspMC/IP Motion Controller / Re: Threading Support Added

« on: February 01, 2009, 03:41:16 PM »

pls email your enquiry to sales@vitalsystem.com or sales@vsi99.com

thanks
Rufi

366

dspMC/IP Motion Controller / Re: Using dspMC and PPort together?

« on: January 30, 2009, 09:14:19 PM »

Printer Port i/o is not accessible with dspmc. 

J4 and J5 on dspmc provide upto 32 inputs and 16 outputs (digital).

regards,
Rufi

367

dspMC/IP Motion Controller / Threading Support Added

« on: January 26, 2009, 01:11:11 AM »

New plugin and firmware are uploaded on DSPMC web page www.vitalsystem.com/dspmc with new features for Threading Support.

will appreciate your feedback on this feature.

regards,
Rufi

368

dspMC/IP Motion Controller / Re: Axis works tuning graphs...

« on: January 15, 2009, 01:14:02 AM »

halkintool,

thanks for reporting this issue.  will get it fixed in the next release.

regards,
Rufi

369

dspMC/IP Motion Controller / Re: Motion controller ethernet not communicating.

« on: January 13, 2009, 12:17:36 PM »

thanks for the note.  will add that in the next revision of the manual.

regards,
Rufi

370

dspMC/IP Motion Controller / Re: Servo amplifiers that work with dspMC

« on: January 02, 2009, 04:29:55 PM »

message forwarded on behalf of Sylvain
-----------------------------------------------------------


We use Omron 400W Servo drivers and Motors for our CNC 5050 Project,

R88D-GT04H              Drive
R88M-G40030H-S2    Motor


The Omron Servo Drive  have Encoder outputs on the CN1 connector,

I have joined a picture of the CN1 Connector, you can see A,B,Z encoder outputs

on the right side, I  think that most industrial servo drivers have theses outputs.

Other info,
I have done some control tests using DSPMC DAC output, the servo drive works best using Speed control mode.

Hope this is of any help!?

Sylvain Demers,  
EPG mecanik Inc.

Visit us www.epgmecanik.com