Messages

41

SmoothStepper USB / Re: Smooth stepper with C25 breakout board

« on: October 18, 2008, 05:09:23 PM »

ok i was find in firmware setup

i was first try yesterday and it seem to work very good, very simple to setup

in the manual, you say that i need to install 4 resistor for encoder input..... can you give me information how to ajust this, and why i need this resistor

tanks
fred

42

SmoothStepper USB / Smooth stepper with C25 breakout board

« on: October 17, 2008, 06:53:05 PM »

Hello

I 'am just remplaced G100 on my milling by smooth stepper,

first :  I will like had more information about the  input/output pins,  it was automatic setup to input or output ??  how mach 3 know if it was input or output ?
can I use this input/output pis to control input/output pin I had on my G320 drive for reset/eneble pin ?

second :  I'am not sure about the use of 4 resistor I need to install on SS.... it was only for the encoder input ? can I use without this resistor ?

tanks
fred

 

43

Mach3 and G-Rex / G-100 hard to connect to mach-3

« on: September 25, 2008, 08:13:47 PM »

it was very long to connect to G100, sometimes it connect without problem but other times, Mach 3 was not able to connect to G100

it write this in alarm on mach3

G100 found
G100 rebooting, re-initialising
please wait....  G100 init....
G100 found
G100 rebooting, re-initialising
please wait....  G100 init....
......

I was try to réinstall mach 3(V3.041) , ré upload firmware, I was try other ethernet cable...
help me

44

General Mach Discussion / Re: Best Computer

« on: May 31, 2008, 03:28:28 PM »

Hood... How mush it was your computer ??


I was buy Compact flash disk with IDE adaptor for remplace hard drive,
The machine vibration was not good for HD

45

General Mach Discussion / Re: Best Computer

« on: May 31, 2008, 03:22:15 AM »

This computer will run only mach3,  no other cad/cam software, I just want optimum performance and fiability computer for run mach3

46

General Mach Discussion / Best Computer

« on: May 30, 2008, 05:47:52 PM »

I am looking to retrofit milling machine, 
I want buy new computer for this and I don't know what is the best mother board to run mach3

on my other machine, I use Asus A8NVN, with Nvidia Geforce grafic card integred... with AMD64 3500+  1gig ram dual

I will like to know if it was the best card or if you know better for mach3

tank
Fred

47

General Mach Discussion / Re: Upgrade to Mach3 R2.56

« on: October 31, 2007, 10:36:39 PM »

I was uninstall mach2 before install mach3...
I was configure mach3 manually better that I can....

I was keep only my screen....

may be I was only one parameter not corect, but I don't know what...
If you can help me......   the bugs was write in my first post....

tank
fred

48

General Mach Discussion / Re: Upgrade to Mach3 R2.56

« on: October 31, 2007, 05:08:44 PM »

I don't need to be refund, I need upgrade of mach 3

49

General Mach Discussion / Re: Upgrade to Mach3 R2.56

« on: October 31, 2007, 04:36:04 PM »

You need money, your software was not perfect

I can paid 160$  for good and stable software, I am just too bad to don't be able to run on Mach3 on my machine

tank
fred

50

General Mach Discussion / Re: Upgrade to Mach3 R2.56

« on: October 31, 2007, 07:46:44 AM »

okay!
 I will réinstall Mach2, Mach3 was not stable, the spindle start without reason and it was dangerous... I am just to bad to had buy new licence for mach3!
tank
Fred