Hello Guest it is January 25, 2022, 02:45:52 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - clachan

Pages: 1 2 3 4 »
General Mach Discussion / Re: PCB manufacturing
« on: February 13, 2008, 02:18:30 AM »
Thank you Chip, got it.

General Mach Discussion / PCB manufacturing
« on: February 12, 2008, 03:37:46 AM »
Has anyone tried to make PCB using much3, what will be the best value hardware set to work with much3 for making PCB?

General Mach Discussion / Re: Please recommend driving board
« on: September 02, 2007, 02:54:28 AM »

General Mach Discussion / Please recommend driving board
« on: August 31, 2007, 06:14:12 AM »
I have retrofitted Dyna 2800, PC with much 3 hooked directly to original Dyna drivers. It was working well, but never consistent particularly in circular cuts. After long investigation, including discussion on this forum, it all came to quality of drivers.

Please recommend drivers for much3 to work with Dyna steppers:
They are made in USA by escape, and have 8 cables coming out of them. Motors data: 1.8 step, 140 watts, serial 0.88 oms 2.3 amps, parallel 0.22 oms 4.6 amps.
Thank you

General Mach Discussion / Re: "run from here" problem
« on: August 26, 2007, 08:39:14 AM »
No, it is not

General Mach Discussion / "run from here" problem
« on: August 23, 2007, 10:41:50 AM »
after hiting run from here button and then start, program runs from the begining instead of from the defind place, any sugestions please

General Mach Discussion / Re: can't contrall Z
« on: June 19, 2007, 09:50:32 PM »
Brett, thank you, works fine now

General Mach Discussion / can't contrall Z
« on: June 18, 2007, 08:57:25 PM »
Can contrall X and Y from keyboard, but Z is not reacting for Page UP no Page Down keys. Z is fanctioning fine when I run a programm and also it runs well from MDI, any suggestions?

General Mach Discussion / Spindle S true
« on: November 24, 2006, 05:06:57 AM »
In Spindle S True window I have all the time wrong reading of the speed, Much applies some kind of ratio to true RPM, don't know how to reset it.
In Spindle Calibration and Testing dialogue box the reading is correct (while the box is open Spindle S True shows correct reading as well, but as soon as box is closed S true jumps up). I can see that Pulses per Revolution box is showing 1, I know that there should be 0 because I have only 1 cut in a disk, but can't change 1 to 0 whatever I tried.

Please help

General Mach Discussion / How industrial is Mach
« on: September 29, 2006, 07:32:24 PM »
I find this software great, without it I can’t see how I could make this thing. I have no any engineering background, and before coming across Mach, I would not even dream about making my own parts – any CNCing was seen as distant unreachable and complicated science. Now I still not a “pro”, but can make parts using mach and desktop mill and lathe.
Having parts designed on a laptop in a Kitchen and then shortly after made in a shed – is thrilling.

Now I have very itchy hands to retrofit bigger machine like old Bridgeport or similar.
The question is how industrial is Mach? My understanding is that it is in complete mercy of Window and noticed that once or twice a week it would through some flukes.
Would you gays run reasonable scale production using Mach as a cnc control of Bridgeport etc. retrofit?

Pages: 1 2 3 4 »