Hello Guest it is April 12, 2024, 10:01:25 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Ben

Pages: « 1 2
11
Finished Screens / TurnSilverBlue.lset screen is black
« on: March 28, 2008, 09:26:41 AM »
On one computer it works fine but the shop computer the whole screen is black except the reset led and the click areas are there but no graphics. I've used the same xml file. What should I check? Thanks, Ben

12
General Mach Discussion / Turn cant find Set file
« on: March 26, 2008, 11:01:34 PM »
All of a sudden (of course I didnt have anything to do with it) Mach3turn cant find a set file. Even after removing all Mach programs and reinstalling 2.63 Mill does ok but turn, as confirmed by ports and pins, either loads the mill set file or none at all.  Any ideas? Thanks, Ben

13
LazyCam (Beta) / Tool save for Turn
« on: January 02, 2008, 09:49:42 PM »
I just bought Lazycam Pro. How do you save a tool type in the Turn side of Lazycam? I'm also having trouble getting it to give me a useable gcode file of a simple curve like the shape of a bullet. TIA, Ben

14
LazyCam (Beta) / Limited to 50 lines
« on: October 24, 2007, 05:27:55 PM »
Lazycam (latest Ver.) acts like it does'nt see my licence. MACH 3 Ver. 2.48 runs fine in the same directory. Help please. Ben

15
VB and the development of wizards / Dosen't see change
« on: October 05, 2007, 09:46:29 AM »
Dim Val
Val = GetOemDro(83)
Call SetOemDro(150,Val)

This gets the current X position and writes it to softlimit Max X but the program dosen't recognize it until I click Config/Homming/limits. I thought the softlimits toggle would cause the program to look there for new info.

16
Mach Screens / Setting softlimits
« on: September 27, 2007, 08:56:13 PM »
I have a Bridgemill, lathe and Mill combo, and my configuration changes quite often. I would like to change my softlimits to accommodate the changes by moving the X and Y-axis to where the new limit will be and press a button to store that position as the new softlimit and display them on screen.
    Has anyone written code to do this or any suggestions? Thanks

17
Tangent Corner / Which Plasma Torch
« on: August 02, 2007, 10:52:54 PM »
Which plasma cutter should I get?  I cut nothing thicker than ¼” and mostly 1/8” steel. It’s non production work in a money limited home shop and I need one that is Mach 3 friendly. Thanks.

18
Forum suggestions and report forum problems. / Email
« on: May 30, 2006, 07:46:29 PM »
I get E-mailed every message that is posted. How do I turn it off? Thanks

19
General Mach Discussion / Display vs table
« on: May 07, 2006, 11:09:00 PM »
Mach 3 mill
I want the display to match what is happing on the table.
Home X = table moves far left to home switch
            Y = table moves  far front to home switch

Config home/limits
      Reversed      Home neg
   X       checked      checked
   Y       xed      checked

Ports & pins
   Motor Outputs
      Dir low active
   X   checked
   Y   checked
Press left arrow key table moves right
Preee up arrow key table moves to front

Cross hairs on display move opposite direction of table

Milling cut moves opposite direction of display

My home switches are mounted on the frame and the table moves to them
Thanks for the help, Ben

Pages: « 1 2