Hello Guest it is March 28, 2024, 07:23:50 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sanlee

Pages: « 1 2 3 4 »
21
General Mach Discussion / How to use Exellon PCB routing file into MACH
« on: February 18, 2008, 02:28:46 AM »
Dear All

Can anybody tell me that how to use Exellon PCB drill and routing file into MACH.

Thanks

sanlee

22
General Mach Discussion / Re: Configuring Start Button as Push Button
« on: January 31, 2008, 04:54:16 AM »
Thankyou Very much Hood

I think M60/M61 is being used by Mach or may he kept reserve but M70 and M71 works perfactly. Thanks again.

Regards

Sanlee

23
General Mach Discussion / Re: Configuring Start Button as Push Button
« on: January 30, 2008, 04:15:12 AM »
Hello Hood and Scott

Thanks, I have already Enabled OUTPUT#5 in Output Signals, then Created file named M60.m1s. in that i have written ActivateSignal(OUTPUT5). then saved this file under MACH3,Macros,Mach3mill. But still it is showing error "No trigger in P word, ignoring M60" when executing M60 in Gcode. please let me know what is P word? Even i have restart my PC also to confirm the updatation of Macros. If in VB script editor i am running then i can see in diagnosis mode that output5 is getting on when ActivateSignal(OUTPUT5) is running. but M60 is not working in Gcode, Please guide me if anything else i have to do for this...

Thanks

Sanlee

24
General Mach Discussion / Re: Configuring Start Button as Push Button
« on: January 28, 2008, 02:45:29 AM »
Thankyou Scott

I have made M60.m1s file and write following thing
'M60
ActivateSignal(OUTPUT5)

and similarly for M61 as deactivate signal. now when writing M60 ro M61 into my Gcode program it is giving following error message.
"No Trigger in P Word, ignoring M60"

Please tell me what to do. I am saving M60.m1s file into "C:\Mach3\macros\Mach3Mill". Is it OK?

Thanks

Regards

Sanlee

25
General Mach Discussion / Re: Configuring Start Button as Push Button
« on: January 27, 2008, 02:17:45 AM »
Hi Scott

Actually i want that my spindle speed should be controlled automatically as per the program when it is running. My Spindle Reley has to respond to custom M-codes in my Gcode interpreter only. and when this particular relay turns off my spindle speed should go into its previous speed i.e. it may be higher or lower. my spindle should remain on till the program is finished and M5 code is given.

Thanks lot

Sanlee

26
General Mach Discussion / Re: Configuring Start Button as Push Button
« on: January 25, 2008, 08:07:49 AM »
Hello Dear

Can you tell me how can i use any Output from Output#1 to 10 as OEM. I have used output#1 as spindle on. actually i have one specific application where my spindle is running in two different RPMs. initially when job is started spindle motor is running arround 5000 rpm and after certain job is completed if i turn ON one relay then it will reduce the splindle rpm by 2500. actually my splindle motor is double winding type. now my question is that how can i control that relay? also it has to be cut off after my turning is over and my splindle will run at 5000 rpm.

Thanks

Sanlee

27
General Mach Discussion / Re: Configuring Start Button as Push Button
« on: January 25, 2008, 07:51:03 AM »
Thank you Cory and Hood

It works very nicely.

Sanlee

28
General Mach Discussion / Configuring Start Button as Push Button
« on: January 23, 2008, 01:17:50 AM »
Dear All

I have 3-Axis CNC Machine running by Mach3. Now while taking production on the machine every time my operator has to press start Button from the Screen using the Mouse. I would like to configure this start button from the outside and want to give Push Button. so that operator does not have to press start button from the PC screen using the mouse. he can simply press the start button which is provided at the external like i have provide an Emergency Button. Can any body help me that how can i configure this start button from the externally.

Thanks

Sanlee

29
General Mach Discussion / Re: threading on lathe
« on: January 20, 2008, 06:43:08 AM »
Thanks Tony

Please let me know that which license you are talking for? i have license MAch3 and OS windos XP is also licensed. Which another licese should i have and from where i should get?

Thanks

Sanlee

30
General Mach Discussion / Re: threading on lathe
« on: January 18, 2008, 05:38:15 AM »
Thankyou verymuch Tony

You are the first one who helped me. Now please do me one more favour i have designed one job for turning into autocad and saved as  dxf. Now i am opening it into the LCAM as turning. then before doing it autoclean, i set the x=0 and y=0 (it does not show z). then doing clean and convert. after that selecting the tool for roughing and finishing and then pressing Pro Demo. No Gcode. on pressing this it is displaying the toolpath. Now my problem is that it does not creat a gcode for Mach3 turning even if i press Post Code key. Or if i am wrong then let me know how to creat post code and open it into Mach turn.

Thanks
Sanlee

Pages: « 1 2 3 4 »