Hello Guest it is March 29, 2024, 04:53:20 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - sanlee

Pages: « 1 2 3 4 »
11
LazyTurn / Re: LazyTurn
« on: December 01, 2008, 05:59:58 AM »
Thanks Dave for the guidance i have tried it by changing mode from radius to dia from the Config/ports & pins/turn option. but the result is still same  ??? no improvement is found. Any more suggessions?

Thanks

sanlee

12
LazyTurn / Re: LazyTurn
« on: December 01, 2008, 03:03:54 AM »
Hi Chip

I have downloaded your file "Copy_3_of_LAZYTURN_TEMP_BLANK.tap" into mach turn vizard but it seems like show below figure. can anybody tell why it is like this? I have licenced Mach3 version R3.02.

Thanks
sanlee

13
General Mach Discussion / Re: Programable buttons
« on: March 02, 2008, 06:05:48 AM »
Josh
Can you give me the macro that you have created for external start button?

Sanlee

14
General Mach Discussion / Re: How to use Exellon PCB routing file into MACH
« on: February 21, 2008, 03:26:05 AM »
Thanks Hood for reply

I downloaded that conversion from Exellon drill file to Gcode which TP has given link. but it is converting wrong cord for x and y at someplaces. i am attaching the original file 3161.nc and converted file 11.txt. jsut have a look.


Thanks TP

I will searh native codes into gcode. but if you have any link then please help. i will grateful to you.

sanlee

15
General Mach Discussion / Re: How to use Exellon PCB routing file into MACH
« on: February 20, 2008, 08:47:43 AM »
Sorry TP

I didnot get you. from where i can change scalling? actually i am asking this because my Gcode is generate in mil (i.e. 1/1000 of inch) and without decimal i.e. like this "X02500Y03000" then it means x=2.500 inch and Y=3.000inch. that is why i want to set DRO as 00000 instead of 0.0000. so from where i can do this.

Thanks lot

sanlee

16
General Mach Discussion / Re: How to use Exellon PCB routing file into MACH
« on: February 20, 2008, 07:41:09 AM »
Yes TP

I have misunderstand with G81 code actually it is for driliing purpose only. so thankyou. but what about the auto tool change in Gcode? also just tell me for my knowledge can we set DRO without Decimal in Inch formate in Mach.? if yes then how can we do this?

Thanks to all
Sanlee

17
General Mach Discussion / Re: How to use Exellon PCB routing file into MACH
« on: February 19, 2008, 04:35:15 AM »
Thankyou both of you

As i have checked that Exellon to G-code converter for drilling file, there is nothing about Z. and all cord are divided by 1000 to convert into inch from the mil. in exellon file they never give Z as Z has to move fixed down to drill. so after every X and Y motion Z will come down hence in exellon formate i think they have not given but internally they may be give signal to Z. i dont have any link but you can see the Exellon machine on website: www.excellon.com. if further you can help me then it would be great for me.

Thanks

Sanlee

18
General Mach Discussion / Re: How to use Exellon PCB routing file into MACH
« on: February 18, 2008, 07:10:11 AM »
Hood

Actually i think these all cord are in mil hence it is having without decimal. and 2nd thing is i dont have the original file. i have only these drilling and routing file only. hence i have to check whether is it possible by MACH to route this file or not. If MACH can do this then it would be wonderful in PCB industries.

Thanks
Sanlee

19
General Mach Discussion / Re: How to use Exellon PCB routing file into MACH
« on: February 18, 2008, 03:13:10 AM »
The 4ch4c01.txt is drilling file while Test-R is routing file. i have tried it to open into MACH but it does not respond. Also in drilling file only X and Y co-ordinates are given for Z nothing is there. so it means after every X or Y or both motion z has to come down for specific depth. am i correct?

Sanlee

20
General Mach Discussion / Re: How to use Exellon PCB routing file into MACH
« on: February 18, 2008, 03:09:09 AM »
Yes Hood

Just see the file as attached.

thanks

Pages: « 1 2 3 4 »