Messages

291

Show"N"Tell ( Your Machines) / Re: Chads new machine

« on: September 18, 2006, 02:39:23 AM »

it would be great if you could take some videos too 

Regards
Fernando

292

General Mach Discussion / Re: Happy Birthday to Art

« on: September 13, 2006, 01:02:34 AM »

Happy bday Art,
Im glad we have you among us!

Great people are hard to find!
Regards
Fernando

293

General Mach Discussion / Re: OEM Mach 3

« on: September 12, 2006, 11:19:09 PM »

duh!
never thought of looking in there!

thanks for the offer, we have an inhouse graphics designer where i work, so he´ll give me a hand.
Best Regards
Fernando

294

General Mach Discussion / Re: OEM Mach 3

« on: September 12, 2006, 10:48:22 PM »

Benny;
I found a good resource editor in the page you sent to me, it the XN reosurce editor. You can change almost everything in there!
I couldnt find the splash screens though, maybe with another editor.

Regards
Fernando

295

General Mach Discussion / Re: OEM Mach 3

« on: September 12, 2006, 09:51:16 PM »

What program did you use to do that?

I have always wanted to build plasma tables for comercial use, I was kind of thinking about doing the mach mod, to bundle with the machines. If you ask me I would think it is kind of a protection both for Art, and for the OEM. If you left the mach program as is. then the consumer can back trace the source of the program and reuse the license if they were inteligent enough to build more machines. If I was the OEM i would purchase a license for each machine built and sold.

Dont know if that sounds reasonable.
Regards
Fernando

296

General Mach Discussion / Re: OEM Mach 3

« on: September 12, 2006, 07:29:33 PM »

thanks benny,
never heard of such resource editors, do you have a preffered one?
Regards
Fernando

297

General Mach Discussion / OEM Mach 3

« on: September 12, 2006, 01:56:21 PM »

Hey, this one goes to brian and art,

I dont know if this is possible, or even convenient for you guys. But is it possible to compile a version of Mach 3 for OEM use? one that shows the OEM´s logo in the splash screen, title bar, menus and helps and abouts?
I guess this will generate an extra cost, maybe an OEM licence?

Regards
Fernando

298

LazyCam (Beta) / Re: LAzycam and THC300

« on: September 12, 2006, 01:51:59 PM »

So basically the only advantage sheetcam has over Lazycam is the kerf width compensation?
Great work brian

299

LazyCam (Beta) / LAzycam and THC300

« on: September 08, 2006, 12:58:55 PM »

Hello all,
I have been talking with Bob Campbell, My main concern of the THC300 he sells is that if it needed to touch off the material every time it needed to make a peirce, it would be very time consuming. He told be that with Sheetcam you can post the gcode, so that it only touches off the material every  time it needs to peirce as long is away from the last time you peirced a set distance you tell it to.
So if you set that distance to say, 12 inches, then if there are 17 peirces within that 12 inches, then it only needs to touch off once. instead of every time.
Can Lazycam do that?
Best Regards
Fernando

300

General Mach Discussion / Re: Tool measure macro

« on: August 31, 2006, 06:44:37 PM »

If the error or deviance is always the same, cant you just add or substract that value to the offset?
Regards
Fernando