Messages

1

General Mach Discussion / After many years away from Mach3 I'm back and older

« on: December 15, 2019, 04:17:34 PM »

 :)I have been away from Mach3 long enough to forget everything I thought I knew. I may humbly ask for your help and guidance. I started using Mach in 1997 so I'm much older and slower so please bear with that. I am working on converting my Plasmacam plasma cutter to Mach 3. Yes I have already hear go to Mach 4. My plan is to get it going with Mach 3 and when I feel smarter I will move on to Mach 4.

2

General Mach Discussion / Re: Installing Mach3 on a Dynamite 2800 machine

« on: November 13, 2009, 02:12:08 PM »

I upgraded my 2800 to run on Mach 3, I had help from a great man down in Florida, Fred. All I did was remove some of the boards, keeping the controllers and installing a breakout board. Very easy and very inexpensive. Fred ended up replacing the motors and some other things on his to get better accurate cuts. When I 1st started mine up it sounded like a army tank rolling by, but putting a better computer on it helped smooth it out some. For me the machine was a mistake, too small a cutting area.

3

Tangent Corner / Re: DYNA MYTE 2800 table top CNC milling machine

« on: January 17, 2008, 12:00:45 AM »

I now went  and bought most if not al the manuals from Dyna at $50 a pop, thank you for the offer, I converted mine to Mach 3 and it runs pretty damn good.

4

General Mach Discussion / Re: Installing Mach3 on a Dynamite 2800 machine

« on: October 12, 2007, 02:38:22 PM »

DM is now charging $50 the the wiring diagrams, could you please contact me at mikeg53549@yahoo.com the machine is now here and I was able to home all 3 axis, now I need to mount the breakout board you recomended.

5

General Mach Discussion / Re: Installing Mach3 on a Dynamite 2800 machine

« on: October 07, 2007, 10:11:55 PM »

Fred:

     I hope to have it home by Sat. Night, yes I have it all figured out on getting it on to the trailer safely. I would really love to not have to spend another $400 on replacing the boards. Did you just put a break out board in and wire to the exsisting board(s)?

6

General Mach Discussion / Re: Installing Mach3 on a Dynamite 2800 machine

« on: October 07, 2007, 06:01:52 PM »

I did buy the one on Ebay Friday and I have to go pick it up next weekend. As far as the controls, I will probably use gecko 201's , run Quantium or Mach and run the same steppers. Not knowing anything about it is a real disadvantage. I'm having a little buyers remorse today, but I'll get over it when the machine is here and I can start working on it.

7

General Mach Discussion / Re: Installing Mach3 on a Dynamite 2800 machine

« on: October 06, 2007, 04:37:46 PM »

I  bought a DYNA MYTE 2800 table top CNC milling machine made by Dyna
Mechtronics. I am looking for a copy of the manual or any information
on it. Anybody have this machine or have experience with one?

8

Tangent Corner / DYNA MYTE 2800 table top CNC milling machine

« on: October 06, 2007, 04:29:58 PM »

I  bought a DYNA MYTE 2800 table top CNC milling machine made by Dyna
Mechtronics. I am looking for a copy of the manual or any information
on it. Anybody have this machine or have experience with one?