Messages

11

Works in progress / Re: Flash RU Screen

« on: June 17, 2010, 12:41:01 AM »

Hello all,

ok ok i know, it is Worldcup in South Africa,, but as somebody the opportunity
to test more the screen ?

I apologise, i have no lot of time actually to continu, but il like this screen, found good ideas
inside, and i think that Pablo need more feedback from our community
to help him in the improvement.

What is your status ?

Fabrice

12

Works in progress / Re: Flash RU Screen

« on: May 22, 2010, 05:20:55 AM »

Good Morning Pablo,

i test again you new version. Nice thing with the Go option.

A question, do you manage the limit display in the Load screen ?
because the information of the size limit of a gcode file  are not displayed.

I wish you a nice week-end,

Fabrice

13

Works in progress / Re: Flash RU Screen

« on: May 17, 2010, 11:40:03 AM »

Thanks for the documentation.

I will look at.

Fabrice

14

Works in progress / Re: Flash RU Screen

« on: May 13, 2010, 02:32:09 AM »

Morning from France,

i reach to implement the macro of Ernis (i suppose) for the Zeroing of the axe Z.
I use a mobile gauge, so x and y are never the same.

Is the field where you put the initial value offset Z the userDRO(2055) ?

Because i like to use this field as manual input of the high of the gauge
(actually it is hardcoded in the macro with a value 20mm)
So i can adapt the macro so that anyone can use it with different gauge.

I miss also the fonction key F5 to start/stop the spindle.
With no flash screen it was possible to modify the screen set, but
i have no idea how to change it in your flashscreen.

Thank's

Fabrice

15

Works in progress / Re: Flash RU Screen

« on: May 12, 2010, 06:47:15 AM »

Hello Pablo,

i have some days off so i will print the macro on paper and learn a bit (little

I hope i reach the goal, because i want to use your screen for my
hobby, and it is important for a good running of the cnc.

What is the fonction of the Lamp ?

best regards,

Fabrice

16

Works in progress / Re: Flash RU Screen

« on: May 09, 2010, 11:36:31 AM »

Hello,

so i am trying to replace some macros (yes trying because i am not able to understand each macro).
I was able to adapt the RefAll macros (because i copied the original orders), but it is an other
way for Probe macro. I use the screen Aqua, that is provided with a macro for the Probe Z high.

Can you explain how the part Probe run. (Initial offset and Z-Touch).
That can be helpfull for me to adapt the macro from Aqua.

A suggestion, if the probe screen is open, you hide a part of the status line.
Can you please dock higher the flash screen ?

Thanks,

Fabrice

17

Works in progress / Re: Flash RU Screen

« on: May 09, 2010, 12:59:04 AM »

Morning Pablo,

thanks for correcting. So i test the wizard on the laptop.
Now it run

But the wizard Rect Pocket doen't open. All other 4 are ok.
I cannot add hole coordinate with the + button, but i suppose
that is the normal way to do ! ok, not so quick, i need to learn
how is the concept.

Best regards,

Fabrice

18

Works in progress / Re: Flash RU Screen

« on: May 08, 2010, 03:10:37 AM »

me again,

so i test the screen now on the cnc pc.
It run under xp 32 bits , and i have not the problems
with the wizard. The wizard generate correctly the gcode.

I need now to unterstand the macros to adapt your screen
to my machine.

Loading of gcode file are also correct, running also.

Next here some news,

Can you open the MDI command field so i can test it to ?

Fabrice

19

Works in progress / Re: Flash RU Screen

« on: May 07, 2010, 11:32:31 PM »

Hello

for the wizard take Surface wizard for example.
For end X and Y value 10, step 1.

I can use any of the 5 wizards, i still have the same problem.
It is the same with entering value or without entering value

I send you a screenshot and the xml config file.
i have problem actually to attach a file to the board,
message error that this file already exist !

The roadrunner file open yet in version 1.31 and 1.33
1.31 with font loaded the roadrunner file.

Fabrice

20

Works in progress / Re: Flash RU Screen

« on: May 07, 2010, 01:53:31 PM »

Hello again;

it seems that the file in error was the example gcode roadrunner from Mach3.

Fabrice