Hello Guest it is March 03, 2024, 10:49:47 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - otpco

Pages: « 1 2 3 4 5 »
21
General Mach Discussion / Re: Time to show off my ATC
« on: January 04, 2013, 07:13:31 PM »
how does the shot pin idea work ? thanks Mark Moog madness

22
General Mach Discussion / Re: Spindle parking (more moog madness )
« on: July 21, 2012, 08:20:00 PM »
hi steve no idea but an early one have been working on it for years . have taken heaps of scrap away ! mine is green . and a Q@C30 taper 25 turret tool changer ,now servoes all round .vfd drive no vari belt ( thank god) just looking intp the tool changer .its a bag of worms i can change it via switches just getting into how to automate it . Drawbar works on air using all the original bits but no oil

23
General Mach Discussion / Spindle parking (more moog madness )
« on: July 20, 2012, 07:06:45 PM »
Hi all I need some ideas for mu moog project . I need to park the spindle at a n exact rotational spot . Maybee adding another  optical index sensor and somehow hooking it to the VDF and doing a jog or something .I am fishing for ideas thanks mark

24
General Mach Discussion / Re: Digispeed not working
« on: April 12, 2012, 05:44:45 AM »
here is some more imformation hope this helps thanks again

25
General Mach Discussion / Re: Digispeed not working
« on: April 11, 2012, 08:08:15 PM »
is this what you need

26
General Mach Discussion / Re: Digispeed not working
« on: April 11, 2012, 06:36:07 PM »
sorry peter . what I have is the pins 1 through to 13 on the bob to pins 1 through to pins 13 on the db25 
 so pin 1 on the bob to pin 1 on the db25

    pin  2on the bob to pin2 onthe db25   etc etc
so bacisly I want the signals to pass through  If I just plug the two db25 plugs together without the bob in the middle the rutex works (but no digi speed ) if I put the bob in the middle the digi works . what I am trying to get to work is both . maybee I should give you a ring .thanks for your time

27
General Mach Discussion / Re: Digispeed not working
« on: April 05, 2012, 10:01:22 PM »
 Hi all sorry for the bad pictures  I have my workshop all packed up .I miss my computer with the things I want and use . I have the homman BOB and digi speed working well . I cant get the output to the rutex working . If I plug the two d25 cables together without the BOB it works fine (the Rutex bit ) I cannot get them to both work together . this is how I have them wired thanks Mark

28
General Mach Discussion / Re: Digispeed not working
« on: April 05, 2012, 08:33:36 AM »
 I will try . it will keep me busy for a while . 

29
General Mach Discussion / Re: Digispeed not working
« on: April 05, 2012, 05:10:33 AM »
Here it is I think and hope ! her is my set up the top plug goes to my Rurex 990 boards the bottom from the confuser

30
General Mach Discussion / any easy way to post pictures
« on: April 05, 2012, 12:53:02 AM »
 Hi all I am trying to post some pictures . Is there an easy way to do it ,.

Pages: « 1 2 3 4 5 »