Messages

1

General Mach Discussion / Go to zero

« on: October 28, 2022, 09:00:42 PM »

Hi all just doing a re build of my Moog 16 years ago I did the mach to my Moog ! Best thing ever thanks Art .. the drives have died .. rutex has finally stopped
 Mach drives now .. so I have the book put again .. when going  go to zero button how do you get z to retract first ? Is this doable . With the reload I can't get this sorted
 Also having a bit of trouble getting the z home to come back off the switch .. thanks to all I do like my mach

2

Show"N"Tell ( Your Machines) / Tuna machdrives bra brc

« on: September 16, 2022, 01:43:57 AM »

Hi I am sinking I am refitting my refit .my original refit had Rutes 990 drives . Thay died ... So 16 years later I am trying to fit machdrives bra drives . I have them fitted but. I cannot get the tuna program to display velocity correctly . This means I cannot tune them

3

Tangent Corner / Re: Sanyo Denki customer service advice ?

« on: October 28, 2020, 12:37:07 AM »

Bump

4

Tangent Corner / Sanyo Denki customer service advice ?

« on: October 21, 2020, 09:21:50 PM »

Hi all still playing with CNC Bridgeport moog is still going but have another project .
 I am not having any luck getting any support from Sanyo Denki for some of there older servo motors .
There site is not very responsive . Has anyone had any luck with contacting them ?
 Trying to get 1987 Microtek up and going again .  CN410T servo motors . would love to find the pin outs for the encoader and tach gen . . thanks to all

5

General Mach Discussion / Re: Mach 3 lost spindle control ??

« on: October 21, 2019, 05:26:17 PM »

well yes and no . think its an 06 ? I got a replacement from you a while ago . Work has been busy so no time to look into it . Think something has gone wrong with the Computer side . I also had a 5 volt supply go west at the same time .It goes to one of your breakout boards . I really need to do an upgrade of the machine control . things are getting old Rutex boards , windows 98 . the list goes on . I have been looking for some replacement for Rutex . Vlad does not appear to be doing anything now . Trying to drive some big DC servoes . ah keeps us young . 

6

General Mach Discussion / Mach 3 lost spindle control ??

« on: October 20, 2019, 11:23:55 PM »

Hi all been away for a while . I have somehow lost the spindle control I have a homman  control running a VFD . I cann not get the spindle to run . Any ideas the vfd is working and the Homman board replaced . . Has any body had this problem . I have not changed any  of the configuration . machine has been running from  2006 . now its decided it needs to stop .. Bugger !

7

General Mach Discussion / smooth stepper support ?

« on: August 26, 2016, 03:01:34 AM »

Hi all is the smooth stepper support working ? there is a few posts that have no response!
would dearly like to get mine sorted out . I need to make things in the shed . Thanks  mark 

8

SmoothStepper USB / ESS Did not respond ?

« on: August 21, 2016, 07:22:43 AM »

Hi all ,.
I am having a few problems with my new to me smooth stepper ..
I am running win7 pro. its the not the usb version.
 I get the message the ess did not respond to wake up message .
Any ideas . I am trying to get this to work so as I can replace my existing computer 

9

General Mach Discussion / Mach 2

« on: September 17, 2014, 12:01:34 AM »

Hi all need to load Mach 2 with the rutex tune any ideas where I might find it . Yahoo wont let me in !

10

General Mach Discussion / Help old Rutex 990 tuneing anybody

« on: September 16, 2014, 09:57:45 PM »

Hi all I need to tune a 990 servo motor board . it has pid tuneing . Is there a way . Art had som sort of a program that went with Mach 2 . Desperate to get going again .