Hello Guest it is January 24, 2022, 11:45:48 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - mick

Pages: « 1 2 3 4 5 6 »
41
General Mach Discussion / Problem with pp port ?
« on: September 22, 2008, 01:47:40 PM »
Hello all,
           The problem i have is getting mach to output 0-5volts on pin14 to control the anolog speed control which is 0-10v.
            In ports & pins /spindle :-step pin 14, dir 8, port 1,
            In motor tuning/spindle :-steps per 1000 , velocity 1500, pulse 3.
            Spindle pullys:-Max speed set 1220 ,ratio 1:1
             
             With the command m3s1220 the voltage on pin 14 changes from  .08volts to .25volts. however if pin14 is setup as dir pin
             on either z or x the voltage swings from .08v to 4.4v .
             
             tried deleteing the xml,s and re-installing mach, but still no joy .
             
             help please,
                               rgds mick.

42
SmoothStepper USB / Re: SmoothStepper & CNC4PC Cards
« on: May 20, 2008, 06:34:08 AM »
hello Simon,
                i have suffered the same problems after fitting the SS to a c11g bob.
after removing the SS the problems persist!.

all the bob i.c,s have been changed hoping to recover spindle control, but no joy!
removed SS plugin,no joy!
reinstalled Mach3,no joy!
looks like a seperate speed controler when my pension arrives.
                                                            regards Mick.

43
LazyTurn / Re: LazyTurn
« on: March 16, 2008, 06:49:52 AM »
thanks Graham,
                     works for me to.
                                                  mick.




44
LazyTurn / Re: LazyTurn
« on: March 16, 2008, 05:21:12 AM »
still no joy,
               mick.

45
LazyTurn / Re: LazyTurn
« on: March 15, 2008, 05:39:02 PM »
RC ,
     NO i dont have sgCore.dll anywhere.
                                                       mick.

46
LazyTurn / Re: LazyTurn
« on: March 15, 2008, 04:27:51 PM »
yes RC,
          I DO have the latest v3.00.2, and the lvkrn15u.dll is also there.
                                                                                                  mick.

47
LazyTurn / Re: LazyTurn
« on: March 15, 2008, 03:40:13 PM »
Hello ART,
              just tried latest Lturn reinstalled twice,still no joy
                                                                                 thanks mick.

48
General Mach Discussion / Re: Urgent - Threading not real time
« on: October 26, 2007, 12:33:15 PM »
hello, Glen
              i had the same problem , it was cured by making the slot in the index disc wider.
                                                                        hope this helps,
                                                                                 mick.

49
General Mach Discussion / Re: Mach3 turn not showing tool number
« on: October 14, 2007, 12:59:45 PM »
drew,
           many thanks for that I,m up and running again.

                                                                            mick.

50
General Mach Discussion / Mach3 turn not showing tool number
« on: October 14, 2007, 10:07:04 AM »
Hello everyone,
                     i have been trying to write a little vb script ,but the tool number is not displayed,the gcode stops and waits
at M6 Txx for cyclestart.

                       using :   tool= getselectedtool()    allways shows zero.

This is not so in Mach3 mill.

HELP please.                           thanks
                                                      mick.

         

Pages: « 1 2 3 4 5 6 »