Hello Guest it is March 28, 2024, 02:59:15 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - biggermens

Pages: « 1 2 3 4 »
11
General Mach Discussion / Mach 3, M98 can get it to work, Please Help
« on: November 21, 2018, 10:15:02 AM »
Hello Everyone

I been messing around with this for days, I got it to work in Mach 4 but not with Mach 3
I do have the 2 files in the Subroutines folde

Thanks

Here is my main program
File name   START.TXT

G20
G54 x11.0 y10.0
M98 P0201 L1
O0201.tap
M30

and i also tried, This one works in mach 4 but not in Mach 3

G20
G54 x11.0 y10.0
M98 P0201 L1
M30

and my subprogram
File name O0201.tap

O0201
N100G00G20G17G90G40G49G80
N110G70G91.1
N120T1M06
N130 (V-Bit {90 deg 1 inches})
N140G00G43Z0.5000H1
N150S24000M03
N160(Toolpath:- V-Carve 1)
N170()
N180G94
N190X0.0000Y0.0000F100.0
N200G00X1.2460Y0.9877Z0.1000
N210G1Z-0.1516F30.0
N220G1X1.2472Y1.0265Z-0.1516F100.0

( Bunch of Code )

N53310G00Z0.1000
N53320G00Z0.5000
N53330G00X0.0000Y0.0000
N53340M09
M99
%


12
Hello

Anyone know how to setup Spindle speed on a open loop setup ??
I tried to set my min speed and max speed in pulley setup that did not help

Any ideas ??

Thanks

13
General Mach Discussion / Re: Mach 3, ESS, Windows 10 Having Problems
« on: August 05, 2018, 12:26:32 PM »
Good Morning Gerry

I had double and triple checked Aspire and Mach everything was in incremental mode and in inches
Now this morning for no reason everything is working fine
The only thing i changed is i installed my Mach 3 license file and everything is fine

I think this machine is possessed

14
General Mach Discussion / Mach 3, ESS, Windows 10 Having Problems
« on: August 05, 2018, 12:59:07 AM »
Hello everyone

I am having a problem here and i cant figure it out
I open Mach 3 and everything seams fine, I enter G00 Y1 and it moves 1 inch like its suppose to
I load my gcode from Aspire and run it, then my machine is all messed up,  i enter G00 Y1 and it moves 22.375 inches
i shut down mach and restart it and everything is fine again until i load a gcode again
I never had problems with Mach 3, Aspire 8.5 and windows xp

Anyone have any ideas ??
Thanks

I am using a ESS board with windows 10
Aspire 8.5, I tried all 3 post processors
I made sure everything is in inches   

15
General Mach Discussion / Re: Knocking X axes, whats going on ??
« on: July 18, 2018, 06:08:13 AM »
Quote
Have no answer to that question. It would be interesting to see the signal output from both since it's the same computer and
and physical pp port.

Yes you are right it would be interesting to see
I just orders a ESS board and going through a pile of extra parts i found a American made 48V power supply, and 4 gecko drives.
That should solve lots of my problems if not all of them :)

Thanks

16
General Mach Discussion / Re: Knocking X axes, whats going on ??
« on: July 17, 2018, 08:22:44 AM »
Hey Rich

I know there is the possibility of noise being produced unfortunately i don't have a scope to test it with
but why would it do it with Mach 3 and not with Mach 4 ???

Thanks

17
General Mach Discussion / Re: Knocking X axes, whats going on ??
« on: July 16, 2018, 10:44:29 PM »
Quote
But Mach 4 works fine
??? Are we talking Mach4 and the Darwin parallel port or Mach3 an the parallel
port?

Both I been playing around with Mach 4 all evening and kind of got it working pretty good, that knock i get in mach 3 is not there, I am not sure whats up with mach 3
I am using the darwin parallel port plug in, i think i will order a ESS tonight

18
General Mach Discussion / Re: Knocking X axes, whats going on ??
« on: July 16, 2018, 05:00:44 PM »
I have tried everything from 25000Hz to 65000Hz I do restart Mach every time and i also do a driver test ever time too and no changes
But Mach 4 works fine

19
General Mach Discussion / Re: Knocking X axes, whats going on ??
« on: July 16, 2018, 12:25:08 PM »
I changed the drives to 3200 @ 10000 pulses for fun ( i know its wrong ) and when switching Y directions the knock got much much worse 

20
General Mach Discussion / Re: Knocking X axes, whats going on ??
« on: July 16, 2018, 10:11:58 AM »
That is awesome Craig Thanks
but what do you think that kock is when i change direction ??
I even unplugged the Y motor and it still knock when you change y direction

Pages: « 1 2 3 4 »