Hello Guest it is December 04, 2021, 09:44:40 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - lumber60

Pages: « 1 2 3 4 5 6 7 8 9 10 11 »
71
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 06:20:25 PM »
Craig is the pitcher , here comes the ball and swing another home run in the same game.

Excellent suggestion and thank you all. i just might win this game.

Ken

72
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 06:13:44 PM »
Well  I hope if she did it was tasteful  LOL.

Ok now here comes the rub, i went through the setup again and changed the pin to low and all seems to work ok. Not to excited but anxious to move on to the next item. Machine works into the wood now.

THANKS TO ALL

Ken the Dummie got educated again!!

73
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 05:44:22 PM »
well i changed over the screen set and found the reverse check box in the motors config. Tried to reverse z axis ,it changed nothing, still backwards  as before. There is no diagnostic tab now.



Ken

74
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 04:29:51 PM »
I don't know how to preprocess

ken

75
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 04:27:36 PM »
OK , i had no idea that this screen was even here. All i have been doing is from the quick response at the bottom of the post page. I read your message and looked all over and found nothing for options. I thought well if i wasn;t the dummy before i am now if i have to post that i can't find it. I started to respond and clicked preview and bang i found it.

ken,

 LOL my wife thinks i am nuts, she herd me say o---------t out loud
let me know if the ayyachment is there

Still laughing errer occured


76
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 02:28:10 PM »

OK try this

https://mail.google.com/mail/ca/u/0/?ui=2&ik=a19f226350&view=att&th=165010a89d9ee276&attid=0.1&disp=safe&realattid=f_jkeblkj00&zwKen

77
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 01:57:51 PM »
Not real sure how to do it. I will swing the bat and see what happens

78
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 01:46:19 PM »
ok this is my screenshot link. Tell me what your ideas are LOL. Kind of going Gooffy

Ken



https://mail.google.com/mail/ca/u/0/?ui=2&ik=a19f226350&view=att&th=16500e380b1f3e3a&attid=0.1&disp=safe&zwcc

79
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 10:05:46 AM »
Yes i did refference your pic on screen and that when i saw your back ground pic was nothing like mine and i had nothing on front pic as you had circled, no reverse there.

Give me awhile and i will have he new profile set up and let you know what is going on.

Ken

80
Mach4 General Discussion / Re: work zero in mach 4
« on: August 03, 2018, 09:12:22 AM »
I saw your screen set in the background and that is not what i have. I cannot find anything under motor config that says reverse.

I am thinking that when i set up inital profile that something is wrong. I thinnk i will try setting up a new profile and go from there.  will my settings carry over if i do that???

Ken

Pages: « 1 2 3 4 5 6 7 8 9 10 11 »