Hello Guest it is March 28, 2024, 01:00:41 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - ElectronicsPnoob123

Pages: 1
1
Mach4 General Discussion / Re: AC Servo Load/Torque VU Meter?
« on: January 14, 2018, 04:34:55 PM »
Cheap  :)

2
Mach4 General Discussion / Re: AC Servo Load/Torque VU Meter?
« on: January 14, 2018, 04:01:58 PM »
Ok no problem, this is for the manual interface i want to use a variety of opto components such as 7 seg diplays bubble displays bargraphs etc due to aesthetics the machine is going to have a small touchscreen i would like an easy view of the position speed and load  ;D

3
Mach4 General Discussion / Re: AC Servo Load/Torque VU Meter?
« on: January 14, 2018, 03:34:54 PM »
Do they work without contact to the conductor? This motor will pull 70A when on full load?


Edit:- can the entire motor cables be put through something like i have attached below?

4
Mach4 General Discussion / Re: AC Servo Load/Torque VU Meter?
« on: January 14, 2018, 10:45:40 AM »
Here you go i have attached the manuals, i have a 750w panasonic motor and drive which the MINAS X manual is for, the other two motors are 1.2KW and 3.8KW made by some chinese manufacturer Yifeng or KRS i think? Ill post you a wiring schematic as its all i could find and a link to the ebay page where i bought them, and thanks alot for helping me out ;D

Link to ebay page:-   https://rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F112411229621

Items are 110st-m04030   and  130st-m15025

Edit:- im also looking for a way to use the speed analog out to write RPM to a 4 digit 7 segment display, i have a couple MAX 7219 drivers knocking around would this just be a case of the arduino measuring either the analog speed ref or the 1ppr Z phase from the quad encoder and displaying on the driver? This is only for the 3.8kw motor as that gonna be my spindle, cheers.

5
Mach4 General Discussion / Re: AC Servo Load/Torque VU Meter?
« on: January 14, 2018, 07:52:55 AM »
Okay cool so would this involve the arduino converting this analog signal to something the LM driver can understand such as a linear scale, i know they have a set of voltage comparators in the chip, im guessing it should be quite a simple job however the other 2 servos i have dont have a torque output monitor - would it be possible to take advantage of the encoder outputs or maybe compare the speed analog output to actual commanded rotation speed to come up with a visual load representation? Thanks   ;D

6
Mach4 General Discussion / AC Servo Load/Torque VU Meter?
« on: January 14, 2018, 07:28:35 AM »
Hi all im trying to make a 10 segment LED VU meter that will output the min and max torque from this servo motor, this will be a spindle load meter for my CNC Lathe, i have searched around but cannot seem to find a noob friendly tutorial about interfacing arduino or some other chip with an AC servo drive, the drive has Quadrature encoder Signals A B and Z out from the encoder of the motor it also has an analog speed and torque output, is there anyway i can make this output as a bar display, i want this to run on an arduino nano v3.0 if there is enough pins if not then it can be a larger one or some other chip, i was maybe thinking some kind of LM series driver for the display which i have uploaded a pic of the ones im using also added schematics of servo drive outputs, any help would be very much appreciated as i haven't a clue where to start with coding im good with circuits though, Cheers.  ;D

Pages: 1