Hello Guest it is March 28, 2024, 04:48:36 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - halfmill

Pages: 1 2 3 4 5 6 7 8 9 10 11 »
1
General Mach Discussion / Soft warning on z max
« on: December 02, 2017, 04:01:39 PM »
below are a few lines of code.  I get the message "soft warning on Z-max". 
G55 setting are: x-10.0000 y-10.0000 z0.0 a0.0   
In soft limit settings, z is set to 0.0000

where is my code wrong for getting this error?  I have no other
z settings in the code except for the g55
please help

(bridge experiment)
%
g0g49g40g17g80g90
m6t0
g64
g20
g0g90g55
g1a-30f3500.0
g01a30f3500.0
g01y0.0625
g01a-30f3500.0
g01y0.1250

thanks bob

2
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 29, 2017, 01:58:47 AM »
My friend asked if Mach 3 could 1. Do Polar Coordinates?  And 2, could Mach 3 also cut a line that moves off center by an angular amount.  So if an right angle from the end that has the smallest angle cuts a slot that is the hypotenuse of that triangle... then can mach 3 if you state the number of degrees of the smallest angle, then will it compute the run of the hypotenuse slot, based on that degree?  I hope this is state clearly enough?
bob

3
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 29, 2017, 01:45:33 AM »
ps to Rich.  I turned off my soft limits and promptly crashed and snapped a mill end (1/8th ") because I don't understand the g-code and how mach 3 treats it near well enough yet...so I think I should stick with soft limits and hard switches for the time being while and I practice and learn...this is my responsibility completely, not blaming anyone...I just need brakes on my car for the time being.

4
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 29, 2017, 01:38:59 AM »
When I went to the hotkeys setup. I clicked A++.  Why call it A++? instead of A+?  Then after selecting A++ I hit the left bracket key. ([).  Then for A-- I hit the right bracket key.  Then I tabbed and got the jog flyout.  If I selected the step jog and hit either of the bracket keys nothing happens!  If I choose the Cont. then the A-axis moves but it appear irrational... if I hit the opposite bracket key it does not return to zero and so forth... it just moves all over the place...so what gives? bob

5
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 28, 2017, 03:16:40 PM »
Rich

In Mach 3  we can use the up-down-left-right buttons etc for xyz movements... but is there a button that will move A-axis??? bob

6
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 26, 2017, 07:18:22 PM »
Points well taken... but I was rear ended as a young man while sitting stopped--at a stop light.  I was injured, the settlement paid for the down payment on my home... ********* does come on its own...   I would not recommend this for people in general... bob

7
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 26, 2017, 12:40:11 PM »
 Rich... are your saying you have no limit switches on your machine for protection...how, how do you keep your machine safe? bob

Once I figure out how to set up the index and pulleys, then I will cover as you suggest .  thanks bob

8
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 25, 2017, 09:54:58 PM »
Rich... in reading Mach Turn pg 4-8, it says..."The limit switches are connected to external logic."  In this case please explain "external logic."   bob

9
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 25, 2017, 04:02:41 PM »
Rich Hi,  downloaded and printed out mach turn, found what you wanted me to see... will study a bit. All other parts have been ordered...thanks bob

10
General Mach Discussion / Re: A-axis rotary lathe question for Mach 3
« on: November 25, 2017, 11:58:02 AM »
I ordered the index pulse card and optical switch.  I will go to the electronics store today for the resistor and hall effect sensors.

Can you give me a short drawing of how the cd and all of this would look in how its attached to the lathe??

I downloaded lesson 8.  Thank you.   bob

Pages: 1 2 3 4 5 6 7 8 9 10 11 »