Hello Guest it is March 29, 2024, 06:15:51 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - Billy De

Pages: 1 2 »
1
General Mach Discussion / Depth Not Changing in Mach3
« on: November 03, 2017, 11:38:09 AM »
OK New Wrinkle...I send a Job from F-Engrave to Tap File....If I set the Depth at  -.0001 or -.0125....The Depth does not change.... I am perplexed...This Just started happening today....

Billy

2
General Mach Discussion / Feed Rate All Over the Board Question
« on: October 30, 2017, 04:45:57 PM »
Hi...Depending on what or who I listen to or calculation I use...To Cut in to Soft Brass ...Higher Lead Content...

I get Feed Rates from anywhere between 4 and 15...

in Inches...I am using a .010 Engrave bit...40 degree angle...1 cutter.. 1/8" x 2".....Max Spindle RPM is 8000...

Would Like to cut at a Depth of  .02"....Still Trying to learn....but I get Feed Rates of ...4.....9.2......and 15......Depending on who's website and formulas I use....

Thank you
Billy

3
General Mach Discussion / 3040T and Z Touchplate
« on: October 17, 2017, 07:10:29 AM »
Hi...I am trying to get info on how to connect a Z Touch Plate on a Chinese 3040T...I can not get any help from Where I Purchased it, Asked for a schematic etc...nothing.... Does anyone know how to hook up a Z Touch Plate with one of these... The 3040T ..Has the Single Cable Output from the Controller to the Engraver...

TIA
Billy

4
Hi Still Learning....Can I set a permanent home position via the g28 code....so when I shut down....x y and z will know where "home is"
in Mach 3 when I start up the next day

5
General Mach Discussion / A Good Source for Bit ?
« on: October 05, 2017, 02:37:00 PM »
Hi...Looking for a Good Source for Bit for CNC 3040..For Soft Brass...bought 30 Pitch .   0.1mm  and bit tip broke 1/2 way through ...can use up to 1/4" round shafts.....Looking for also 0.2, .03, .04. .05, .06...For our other machine we Get our Bits From Anteres but they do not sell shorter CNC Bits...Any suggetions would be appreciated

Billy

6
General Mach Discussion / Is there a way to slow the speed of x and y
« on: October 03, 2017, 12:54:40 PM »
Hi...Started to experiment with some brass....The x and y move too fast for the brass.... I have tried slowing the feed rate....
Other than Motor Tuning.....How can I slow the x and y movement........????

Billy

7
General Mach Discussion / Can not seem to carve out a simple box ?
« on: September 26, 2017, 11:10:10 AM »
Hi, I am trying to make a simple cut out in wood.....4x12 that i will use as a template....I have use the V-Carve Option, the Inlet Option. When I save its as a DXF...Convert in Lazycam to a Tap...Bring in Mach 3.....All I get is an "Empty" box with nothing in the middle to carve out..

Getting frustrated
Billy

8
General Mach Discussion / Cutting / Engraving only the Fill ?
« on: September 22, 2017, 12:39:45 PM »
Yet Another Question...Is there a way to cut only the "Fill" of Text or The Fill of a BMP, Tiff File etc...Not The Oultine ?

So Far So Good On my Other 2 Questions

Billy

9
General Mach Discussion / Z Depth ??'s
« on: September 21, 2017, 01:20:42 PM »
Hi...Newbie (Still)...I have tried setting the Z Depth but does not event touch .....I am using a 3/16 thick piece of brass to set my "0"....
I go in to the material thickness....Set that to .1875......Nada....I am perplexed ....x and y go where they are supposed to...but not the z

Billy

10
General Mach Discussion / Single Line Cut for Plates
« on: September 19, 2017, 10:23:40 AM »
Hi...Trying to figure out if there is a way to have engraver only make one cut...like a single line font...Cut each letter only once...not each side of the letter...Hope I am Making Sense.... On our Dahlgren...If we use a single line font...it only makes one stroke/pass...like down the middle...
not ...The left side if the "I"...The Right Side of the "I"....ect

Billy

Pages: 1 2 »