Messages

21

Mach4 General Discussion / Is there an M06 macro with G43 height compensation?

« on: November 26, 2022, 04:05:56 PM »

Hi, I'm using a translator.
Is there an M06 macro that uses the spindle nose as zero?
all subsequent tools will refer to that zero point and with G43 H... the correct measurement will always be obtained.
I use Mach4 on the lathe (with a CsLab)
now I would like to use it on the pantograph (with the Smooth Stepper ethernet).
on the mill I use Rosetta CNC, and I use that G43 H system ... with success.
if it can be useful I put the link to have at least an idea of what I would need.
https://www.youtube.com/watch?v=agODOhWnJjs&t=449s
I would like to use the same system also with Mach4.
thanks!

22

Mach4 General Discussion / Re: How to remember DRO and Fixtures in Mach4?

« on: November 23, 2022, 01:15:05 AM »

it would be an impossible mission for me ... I would only do damage ..

23

Mach4 General Discussion / Re: How to remember DRO and Fixtures in Mach4?

« on: November 21, 2022, 06:54:19 AM »

I don't understand what to do!
I'm not a programmer!
is it not possible to create a Fixture Save button like in Mach3?

24

Mach4 General Discussion / Re: How to remember DRO and Fixtures in Mach4?

« on: November 20, 2022, 04:47:45 PM »

how can i load the.ini file?

25

Mach4 General Discussion / Re: How to remember DRO and Fixtures in Mach4?

« on: November 20, 2022, 03:24:57 AM »

Hello.
I tried putting the code you wrote inside the Custom Button.
no result.
Origin of the piece made and button pressed.
if i turn off the power to the pc i lose origin.

26

Mach4 General Discussion / Re: How to remember DRO and Fixtures in Mach4?

« on: November 19, 2022, 06:11:42 AM »

well! I thank you!
I'll try, then let you know

27

Mach4 General Discussion / How to remember DRO and Fixtures in Mach4?

« on: November 18, 2022, 05:52:01 AM »

I'm using google translate, sorry for any mistakes.
How can I make Mach4 remember the last seen position in the DROs, the next time the program is reopened?
How can I save the fixture G54, G55 etc etc?
I asked this question, because sometimes the electricity goes out.
When this happens I lose fixture offset.
thanks!

28

Mach4 General Discussion / Re: Lathe machine G76 thread work problem (video attached)

« on: September 27, 2022, 02:21:37 PM »

I own CSMIO / IP-S
I don't have any problems.
https://www.youtube.com/watch?v=8t_bZMwJSBk

29

Mach4 General Discussion / Re: G code to change rapid speeds

« on: December 16, 2021, 03:57:57 AM »

no, I want to decrease the maximum speed of the rapid.
tested the first gcode, the quick value will be reported to 100%

30

Mach4 General Discussion / Re: G code to change rapid speeds

« on: December 16, 2021, 02:15:05 AM »

the macro works
but that's not what I wanted to do.
your code moves the slide.
I own CsLab CSMIO-IP / S.
I associated Feed + Rapid with the same potentiometer via plugin.
consequently the plugin takes priority over control.
to make it work it is necessary to impose the limit threshold on Mach4, and not on the functions.