Messages

51

Mach4 General Discussion / Re: Lines in the tool path window

« on: October 24, 2017, 05:14:57 AM »

I met the same problem. The lines on the Tool Path display are very thin (not the GCode window). There are no settings for the thickness of the lines. This problem appears on the PC integrated Video Card.

52

Mach4 General Discussion / Re: Mach4 MDI Password

« on: July 05, 2017, 02:40:10 AM »

MDI tab password - Artsoft

53

Mach4 General Discussion / Re: Mach4 - Constant Velocity & Exast Stop.

« on: June 16, 2017, 02:18:27 AM »

Mauri
Photo number 2.
My Velocity = 25000 mm/min (On M4 there will be 40000 mm/min)
My Acceleration = 5000 mm/Sec^2 (On M4 there will be 8000 mm/Sec^2)
At M4 Tulpath does not have time to update at this speed.
At M3 time.
CV is better to adjust the resolution, rather than viewing.
-------------------------------------------------------------------------------------
The result, a new mcCvTuningWizard from Chaoticon works.
There was a new problem. When you start the gcEdit, you receive an error:
9:12:42 AM: Invalid value 2 for a boolean key "WholeWord" in config file.
9:12:42 AM: Invalid value 4 for a boolean key "MatchCase" in config file.
I installed M4-Demo on another PC, it works.
Put a wizard mcCvTuningWizard and after the restart of M4 error began to appear and on this PC too.

54

Mach4 General Discussion / Re: New CV tuning wizard

« on: June 15, 2017, 10:08:06 AM »

Thank you, Chaoticone.
I tried the wizard in my work, it looks like it works and works well.
But, I ran into a problem. If you run the wizard, turn it on, it works. If you go into the configuration - mach..., close the settings, then the wizard turns off.
It is possible that it would always be included, even with the first launch of Mach4?

55

Mach4 General Discussion / Re: New CV tuning wizard

« on: June 15, 2017, 04:08:05 AM »

Hi, Chaoticone.
local cmd = "explorer.exe /open," .. dir .. "\\Docs\\mcCvTuningWizardHelp.pdf"
Where can I find mcCvTuningWizardHelp.pdf ?

56

Mach4 General Discussion / Re: Mach4 - Constant Velocity & Exast Stop.

« on: June 15, 2017, 01:57:48 AM »

Here is a video of the work of Mach3 in CV mode.
https://www.youtube.com/watch?v=_vTpwuikrAQ
When you change the speed at the corners and arches the car travels smoothly and does not jerk. The arc is on a detail of complex shape and consists of many small parts.

57

Mach4 General Discussion / Re: Mach4 - Constant Velocity & Exast Stop.

« on: June 15, 2017, 01:35:24 AM »

Chaoticone,
Thank you. If I'm not mistaken, then mcCvTuningWizard was not in the assembly 3390. I'll try it in my work.
Mauri,
Thank you. Google translate is not entirely translates your message. What speed of cut do you have and acceleration? If the acceleration is not large, then Wizard_CV_Federate works normally. If the acceleration is large, even with a small decrease in speed from the working speed, a blow is seen with a change of speed, the mechanic of the machine suffers. And on Mach3 there are no such problems, everything works well.

58

Mach4 General Discussion / Mach4 - Constant Velocity & Exast Stop.

« on: June 14, 2017, 07:50:20 AM »

Hi guys!
Sorry for my English!
I use Mach4 4.2.0.3390 (Hobby), ESS with the plugin 202, Laser source IPG Photonics.
It is not possible to adjust the cut at high speed and acceleration at a constant speed. The exact stop mode does not suit me, because on a thick metal the corners melt, on a thin metal on complex trajectories the machine jerks violently. After reading the forum, I learned about Wizard CV_Feedrate, but it does not work. At high speed and acceleration the machine starts to twitch. In Mach3 there is a tuning of the CV Dist Tolerance and Stop CV on angles, which work as it should. But, I did not find such settings in Mach 4. The G64 code has additional parameters G64P()Q(), where P is the rounding tolerance, Q is the simplification tolerance. On LinuxCNC this is working, on Mach4 it does not work.
I would like to use a new Mach4 and its capabilities on my machine, but I can not. Forgive help.