Hello Guest it is March 29, 2024, 02:05:58 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - SEREGIUS

Pages: « 1 2 3 4 5 6 »
11
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 30, 2018, 02:35:12 AM »
Excuse me. Yes, mm. Thank Tweakie.

12
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 30, 2018, 01:27:18 AM »
What is the maximum speed on this machine?
Tested Mach4 at speeds of 20,000 mm / sec and higher?
I need to cut the metal at a speed not lower than 25000 mm / sec.
I will try to set the speed in the gcode 20000, 10000, 1000. And see the changes.

13
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 30, 2018, 12:30:25 AM »
Mauri,
Sorry for my English.
I installed 1500, as you advised - the circles are not even.
I started the old wizard. Make sure that the CV mode is on. Set the speed to 500. The wizard counted the speed. I restarted Mach4. The circles are not even.
I have a machine for cutting metal with a laser (1500 W). http://forum.machsupport.com/forum/index.php/topic,35121.msg241204.html#msg241204
Backlash compensation I do not use. I do not use a reduction. Motors are attached to the toothed rack Gudel.
Tell us what additional information is needed.

14
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 29, 2018, 02:15:10 AM »
Hi Mauri,
I was able to check the speed change. There are no changes in the section, there are absolutely identical circles. I launched another wizard, CV mode is on. I set the maximum speed to 500 and restarted mach4. There is no change in cut, equally curves. ((((

15
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 27, 2018, 06:19:42 AM »
I use the HIWIN TMH93E series rotary engines.
Now the machine cuts thick metal, I do not know how many hours are left until the end of the cut, there is no estimated test time in Mach4. Then I will try your recommendations.

16
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 27, 2018, 05:30:55 AM »
Mauri,
Files containing GCode posted in post number 2. 1359.TAP - no problem, 1360 - problem.
The lines of Gcode look like this:
M03
G01X60.64Y105.40
G03X60.36Y15.60I60.50J60.50
G03X60.64Y105.40I60.50J60.50
M05
I could not translate this string - (What are you making to run your machine so fast?)
Are you asking for a quick setup of a new car or a quick move? Or other?

17
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 27, 2018, 01:52:36 AM »
Mauri,
Better to use mcCvTuningWizardBeta3, or other Wizard?
What to change in mcCvTuningWizardBeta3 so that it produces lower speeds immediately.
I found the string [CV Feedrate]. The first 10 lines:
Angle_0=56568.000000 (The maximum speed is set to 40,000)
Angle_1=37642.000000
Angle_2=18821.000000
Angle_3=12547.000000
Angle_4=9398.000000
Angle_5=7518.000000
Angle_6=6248.000000
Angle_7=5359.000000
Angle_8=4699.000000
Angle_9=4165.000000
Angle_10=3759.000000
What speed do you recommend setting?
In machine.ini there is a line [CVBlendRadius],  what does it do?
I added a file machine.ini.

18
Mach4 General Discussion / Re: Mach4 + ESS CV tuning wizard problem
« on: November 26, 2018, 05:17:07 AM »
G-Code

19
Mach4 General Discussion / Mach4 + ESS CV tuning wizard problem
« on: November 26, 2018, 05:08:01 AM »
Hi,
Search in the forum does not work, write to the old forum messages, an error appears.
http://forum.machsupport.com/forum/index.php/topic,34966.0.html
http://forum.machsupport.com/forum/index.php/topic,35121.msg241239.html
I again had a problem with cv.
I made a new car, Mach4_3835+ESS+Servo HIWIN.
The maximum speed of 55,000 mm / min, acceleration of 20,000 mm / s / s.
Now installed 40,000 mm / min, acceleration 1500 mm / min (test and tuning ...).
To configure CV I use mcCvTuningWizardBeta3 . This version is recommended as the latest and there are no errors. (I can not find the topic on the forum, the search does not work.)
I have been looking for the cause of the problem for a long time and it seems that I have found it.
If the circle consists of two halves, Mach4 distorts the trajectory (Mach3 does not distort).
If the circle consists of one circle, Mach4 does not distort the trajectory (Mach3 also does not distort).
How to set up Mach4 for it to work?
Photo cut, files Gcode, settings added.

20
I'm interested in this question...

Pages: « 1 2 3 4 5 6 »