Hello Guest it is March 29, 2024, 07:40:24 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Johnansaro

Pages: 1 2 3 4 5 6 »
1
General Mach Discussion / Re: ATC Spindle How to set them up?
« on: May 04, 2018, 02:12:09 PM »
Hi TPS

Thanks for the reply
and please forgive my lack of knowledge.

Ok what i was trying to do is as follow:
Let's say that I have connected my Chuck Open sensor to Input1 (I assume that they are On and Off Type of sensors), When it is off that things are Ok,
and it should proceed with ATC procedure,
But if it is on then What i think, I want to do is to shut off the Machine or sort of Estop it, I think M5 code just stops the spindle.

Please tell me if my logic is OK, should mention that my knowledge of ATC spindle is close to none, and I  need to work on it a lot, so please bare with me.

regards

2
General Mach Discussion / Re: ATC Spindle How to set them up?
« on: May 04, 2018, 12:56:28 PM »
Hi TPS

Thanks again, but I already knew about these pdf files. Needless to say that they will take a lot of time to read.

Meanwhile I appreciate greatly, If you could clarify this sensor issue for me.
The codes that I posted before, is it going to do the Job? Do I need to add more lines?
Could you direct me to some sample codes on this matter?

regards

3
General Mach Discussion / Re: ATC Spindle How to set them up?
« on: May 04, 2018, 10:54:33 AM »
Hi TPS

If I need to address them could it be done like below;

If IsActive(input4) Then
Code "M5"                         Trying to stop everything, If there is better way please let me know
End if
Exit the Sub

Regards

4
General Mach Discussion / Re: ATC Spindle How to set them up?
« on: May 04, 2018, 10:18:37 AM »
Hi TPS

thanks for the reply
this is what i thought to be, do you know what is the Script code that address them?
Let's say that i have dedicated Input4, Input5, and Input6 for my sensors.
do i need to address them in my M6 Codes, If yes please tell just the few lines needed for this matter.
also could it be like a Limit switch or Estop, that I do not need to address them and they just stop everything when they are turned on?

Regards
jhonansaro

5
General Mach Discussion / Re: ATC Spindle How to set them up?
« on: May 04, 2018, 02:37:06 AM »
Hi again TPS

I do not have a manual, it is very hard to get one I have searched the net, but no success.
As I said it is very similar to famous HSD brand, The spindle is installed by the person whom I purchased from, it was sort of easy, and it is working.
My question is very general, Basically what is the general procedure on operating one? Particularly on its sensors relation with Mach3, Do I need to address them in my codes?
Or is it being handle by the Spindle itself sort of a hard ware issue and not a software one?

regards

6
Hi TPS

Ok, many thanks

regards

7
General Mach Discussion / ATC Spindle How to set them up?
« on: May 04, 2018, 02:19:27 AM »
Hi there

Could some one direct on how to set up an ATC Spindle, I am trying to Install a CC spindle, which is a copy of HSD,
Just a general Guide I need,
particularly on its sensors, do I need to address them in my ATC VB Scripts?

regards
jhonansaro

8
Hi TPS

Thanks a lot for the reply. Ok That is good,
But Is it any other way of protection on the VB codes and/or the editor?

Regards

9
Hi there
is it possible to password protect the VB Editor and/or its scripts?
I do not want my VB scripts to be changed or modified so easily by everybody.

regards
jhonansaro

10
General Mach Discussion / Re: wait action in macros
« on: May 04, 2018, 01:22:59 AM »
Hi there

thanks every body, I am a lot clearer on this issue.

regards
jhonansaro

Pages: 1 2 3 4 5 6 »