Hello Guest it is March 28, 2024, 08:09:38 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Chuckcoe

Pages: « 1 2 3 »
11
General Mach Discussion / Re: Mach 3 screen
« on: May 06, 2017, 06:59:22 PM »
Yes, finally, thank you so much


12
General Mach Discussion / Re: Mach 3 screen
« on: May 05, 2017, 02:57:11 PM »
try again

https://goo.gl/photos/GmGuhrgF8eBQXp5r7

sorry about that,can't type either

13
General Mach Discussion / Re: Mach 3 screen
« on: May 05, 2017, 02:54:52 PM »
Ok, here is a link to my controller photo's.

Take a look and see if I have any options other than buying a new control box

https://goo.pl/photos/GmGuhrgF8eBQXp5r7

Thanks
Chuck

14
General Mach Discussion / Re: Mach 3 screen
« on: May 03, 2017, 12:04:08 PM »
Also how do you make hot topic ?

15
General Mach Discussion / Mach 3 screen
« on: May 03, 2017, 12:01:13 PM »
What am I doing wrong ?  When I import g-code from makercam the image is nothing but a big blob of pink. I go toolpath and it is the same, do cycle start and it goes around in circles. I have watched video's ( oldgeezergeek ) did the same albert jpg., followed all the same steps andstill ended up with a blob.
I own Mach3, is not demo !!!!!

Help
Chuck

16
General Mach Discussion / Re: Auto zero wiring with uc100 adapter
« on: May 02, 2017, 09:04:37 PM »
Sure, how do I do that on here?

17
General Mach Discussion / Re: Auto zero wiring with uc100 adapter
« on: May 02, 2017, 08:01:22 PM »
Also have a probe small plastic circle thing with small aluminum center w/ black, white wire w/ alligator clips. Best I can describe

18
General Mach Discussion / Re: Auto zero wiring with uc100 adapter
« on: May 02, 2017, 07:54:14 PM »
I don't know, where would I look for that. A db25 board came with a parallel cable but was not used, instead bought a uc100. There are a couple of other ports on the back of the control box, one of which is the 4th axes plug. The other looks like a printer port cable.
I have Chinese machine since I am just starting this cnc life. I am 67 y.o and probably over my head. Fairly well computer ok, can read & write and follow instructions w/pictures ( just kidding on the picture part ), but will take it if I can get it.

Thanks for the assist
Chuck

19
General Mach Discussion / Auto zero wiring with uc100 adapter
« on: May 01, 2017, 07:55:08 AM »
Is there any instructions in wiring probe with uc100 being used instead of p/p. Also it would help if I was for dummies . I have looked everywhere and either I am wording it incorrectly or I need more help than I think
Thanks Chuck

20
General Mach Discussion / Re: Scaling Mach3 imported dxf files
« on: April 24, 2017, 10:24:57 PM »
X10 Y10 stock thickness 3/8" everything is in inch,
Dxf file imported values 220,456, 195,434, 0,000
Set scaling to 10X10X0.375
Result is a 2X2 that is unrecognizable

Hope that answers question

Pages: « 1 2 3 »