Hello Guest it is May 17, 2024, 08:22:22 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Firechief

Pages: « 1 2 3 »
11
Mach4 General Discussion / Lua editor
« on: January 09, 2018, 04:52:18 PM »
I just got a new computer for my router with window 10 everything installed ok imported my old profile, everything is there.
when I try to open the PLC script it gives me a error can not open the lua editor. I can not open any button script as well... same error.

Any help would be great
Thanks

12
Mach4 General Discussion / Re: Tool Finding
« on: January 09, 2018, 09:20:05 AM »
I,m working in the Lua code with a coroutine. Got everything working finding all XYZ just need to get the center of the bit not the edge on the XY.
Thanks for your help

13
Mach4 General Discussion / Tool Finding
« on: January 08, 2018, 02:47:57 PM »
I heed some help with finding the current tool edge. I working on a XYZ 0. I got it to find XYZ 0 but the setting is to the side (XY) of the tool not the center. Any help with the lua code would be great.
Thanks


14
Mach4 Videos / Re: Creating an M6 Toolchange in Mach4 (Part 3)
« on: May 08, 2017, 11:16:26 AM »
All my testing was done in the MDI window this M6 code work great... when I run it in the gcode it would not set the tool to the right height. (way off). What I found was the post Processor was adding a tool offset to the gcode on the next line in the gcode. I mod the post processor and remove it and then all was well. Big thanks for all your code.



Tim Smith


 

15
Mach4 Videos / Re: Creating an M6 Toolchange in Mach4 (Part 3)
« on: May 03, 2017, 11:22:30 AM »
Just another point I found in the code you may like to fine tune. when the Z move up to your set point Z0, my Z0 will trip my limit switch. Sounds dumb but it took my some time to find out why it would not run the tool change. reset it to -2 and all was good.  :D
I'am just glad that the code is starting to make some logic to me. [Little]

BIG THANKS
firechief

16
Mach4 Videos / Re: Creating an M6 Toolchange in Mach4 (Part 3)
« on: May 01, 2017, 02:05:14 PM »
I have used your tool change code.. after a little set in inch's it works great. One thing I would like to do is have the code turn off the spindle and wait for 12 sec or have the VFD trip a spindle has stopped before it moves. The Post code from Vcarve has the start up of the spindle and is working good.

Big thanks to your help as I have used other code and it always is great. Please keep up your help, there is a lot of us that need it.

Firechief

17
Mach4 General Discussion / Re: Post Processor
« on: February 11, 2017, 10:38:50 AM »
Thanks all for your help.

18
Mach4 General Discussion / Re: MACH4 EGDE FINDING
« on: February 10, 2017, 09:11:51 AM »
Big Thanks, That should help me out.


19
Mach4 General Discussion / Post Processor
« on: February 08, 2017, 01:33:37 PM »
What post processor do I pick when using VCarve pro 8.

firechief

20
Mach4 General Discussion / MACH4 EGDE FINDING
« on: February 08, 2017, 01:22:50 PM »
I need some help with setting up mach4 with edge finding routine. How do you use a edge finder and set all the variables that go with it. Lot of help with Mach3 but not a lot with Mach4.
Please can some one make a video or manual that can explain the basic. with all the setting you need to do before you click cycle start.   ???

BIG THANKS

Pages: « 1 2 3 »