Hello Guest it is August 12, 2020, 03:29:44 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Azalin

Pages: « 1 2 3 4 5 6 7 »
11
PoKeys / Re: What causes "Weird signal from device" error?
« on: February 28, 2018, 05:10:41 PM »
By the way, I have tried the firmwares bellow but lathe encoder does not work with these firmwares so I stick with 4.2.39.

PoKeys v4.3.14 Configuration and PoBlocks (13.2.2018).exe (39.47 Mb)
PoKeys v4.3.6 Configuration and PoBlocks (3.1.2018).exe (39.41 Mb)
PoKeys v4.3.8 Configuration and PoBlocks (13.1.2018).exe (39.47 Mb)
PoKeys v4.3.9 Configuration and PoBlocks (16.1.2018).exe (39.54 Mb)
PoKeys v4.3.9a Configuration and PoBlocks (17.1.2018).exe (39.54 Mb)

12
PoKeys / What causes "Weird signal from device" error?
« on: February 28, 2018, 05:08:45 PM »
I'm using a PoKeys57E with cnc4pc M16 board. Machine is a lathe. It works fine when it works but I often get this annoying error. Once I see it the machine then stops responding and then a "Connection with the device is lost" error comes promptly. The only thing left is to power-off/power-on 57E and restart Mach4.

I have checked all the wiring to make sure if I have a grounding loop but everything looks fine.

When I first get the 57E from cnc4pc it had v4.1.xx firmware installed. I then updated it to PoKeys v4.2.39 but nothing changed.

Anyway, what causes this error? Is there anything I can do/check?

Thanks,
Suat

13
PoKeys / Re: Firmware problems 57E
« on: February 08, 2018, 02:16:34 AM »
Hi Matevž,

Lathe encoder doesn't work with the latest firmware. In the PoKeys diagnostigs screen I can see the pins 8, 12, 13 are flashing when I spin the spindle with my hand but Mach4 doesn't receive an RPM value.

It was working perfect with the old firmware. I downgraded the firmware to v4.2.39 and lathe encoder works now. Card is 57E by the way.

Is this a bug of 4.3.9a?

14
PoKeys / Re: Firmware problems 57E
« on: February 07, 2018, 04:07:37 PM »
Sorry bringing up this old thread.

How did you downgrade firmware of 57E? Where can I find an old firmware? I need to flash fw version 4.1.2 (or similar) but I have no luck on finding the old firmwares.

15
Mach4 General Discussion / Mach4 ShuttleXPress/Pro problem
« on: February 05, 2018, 09:32:20 AM »
I'm using the lathe screen set. The slider that adjusts sro works fine. When the speed is 100rpm at 100% the RPM at 150% is 150rpm. No problem there. But the "spindle override ++" increases the speed about 1000%

I have only one spindle setting. 100 min and 1500 max.

Sent from my MI 5s Plus using Tapatalk

16
Mach4 General Discussion / Mach4 ShuttleXPress/Pro problem
« on: February 04, 2018, 07:14:31 AM »
I've assigned a button to "spindle override ++" and other to "spindle override --". When I click the ++ button it increases the RPM by 1000rpm. Same for the -- button. What I prefer is to increase or decrease the speed by 50 RPM per click. Can I do that?

Sent from my MI 5s Plus using Tapatalk

17
Mach4 General Discussion / Shuttle Pro Plugin!!!!
« on: February 04, 2018, 07:09:14 AM »
Found it.

Sent from my MI 5s Plus using Tapatalk

18
Mach4 General Discussion / Shuttle Pro Plugin!!!!
« on: February 03, 2018, 05:08:11 AM »
My ShuttlePro works fine except the inner wheel. The selected axis moves 1mm per pulse but I want it to move only one step per pulse. Is there a way to this? I've played with Mach4 mpg settings acceleration and velocity but it didn't help.

Sent from my MI 5s Plus using Tapatalk

19
Mach4 General Discussion / Re: Mach4 ShuttleXPress/Pro problem
« on: January 26, 2018, 08:42:01 AM »
Yes, it worked. Thanks.

20
Mach4 General Discussion / Re: Mach4 ShuttleXPress/Pro problem
« on: January 25, 2018, 08:21:43 AM »
Hello Suat,

Try this: Go to Configure>Mach>MPGs and check the 'Reverse' box for the MPG you have assigned to your ShuttlePro. This should change the direction of travel for the inner wheel.

All the best,
Bryanna
Thanks. I'll try when I get home.

Sent from my MI 5s Plus using Tapatalk

Pages: « 1 2 3 4 5 6 7 »