Hello Guest it is March 29, 2024, 04:48:11 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - KatzYaakov

541
Mach4 General Discussion / Re: hold all axis also on jog
« on: April 01, 2019, 07:24:19 PM »
thanks
can you please explain  about that command
mcCntlMacroAlarm(in document its that said its force in alarm state ,but its actually do?)
and what is parameter 5000-5006

542
Mach4 General Discussion / Re: hold all axis also on jog
« on: April 01, 2019, 07:13:20 PM »
i dont like this way because its look to complex for this base comand(do not forget
i need to remember the curent speed ,then put them again while condition pass ,so its become much complex ,and
as i mention its not only before homing its also in some other cases
so then i got what mach warning against ,try avoid heavy on plc script
but also other much more problem for me its that the jog command as i copy from yours sample not turn to "0"
in my laptop

543
Mach4 General Discussion / Re: hold all axis also on jog
« on: April 01, 2019, 06:54:40 PM »
when i disable the axis i think i will get the output enable "0" then servo driver will turn too "bb" insted of "run"
this very bad
as i mention its not condition only  before homing
its command to "hold" in some other cases
for example while force one of the cylinder that can accident

544
Mach4 General Discussion / Re: hold all axis also on jog
« on: April 01, 2019, 06:26:10 PM »
second reason im not sure i can use it  ,is that i use external potenziometr to control both G0 G1
i think there will be conflict between that 2 commands
there must be much more easy way to hold all axis ,its basic safety command not only when no homing ,but also in some
mechanic sondition

545
Mach4 General Discussion / Re: hold all axis also on jog
« on: April 01, 2019, 06:21:59 PM »
now in my laptop its 29% while in the machine it was 20%  strange

546
Mach4 General Discussion / Re: hold all axis also on jog
« on: April 01, 2019, 06:08:46 PM »
hi
thanks for fast answer
i already tried it
but in the Jog its not give 0 its give 20% even we put 0

547
Mach4 General Discussion / hold all axis also on jog
« on: April 01, 2019, 11:43:12 AM »
hi
i want add simple condition ,that if....
not any movement can happened
not on reference
not on G0
not on G1
and not on manual move
very very simple request but cant find hoe do it

548
Mach4 General Discussion / Re: Mach4 Output Config. gets lost with shutdown
« on: February 26, 2019, 04:19:01 AM »
hello
i just stand to write new topic with almost same problem
when i turn on my mach (all was close as need) i cant make homing
 z and a(magazine) make home well ,but x y go to home switch but not make the cycle ,and axis's stack on over limit
and i can try 5 times same
but if i restore backup from day ago its make it without any problem
maybi there any bug with save the ini file?
thanks alot


549
i have the magazine on gantry
and i want when i go to change tool that gantry will move to next x position ,and y go to load the tool,but x not need be conect to loading
cycle
like this order:
x move to next x position(its just move no one care if reach position or not)
y z a(a is the rotary magazine) make the tool change without any consider about x movement
after finish the tool change ill check if x reach the point then continue
thanks
yaakov

550
Mach4 General Discussion / Re: delay
« on: February 14, 2019, 01:23:02 AM »
thans smurph but this was my first try but didnt work
ill try with put in registry global parameter that will change state
thanks