Hello Guest it is March 29, 2024, 12:44:03 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Stuart

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 »
141
Mach4 General Discussion / Re: Mach 4 not stopping at manual tool change
« on: January 01, 2019, 09:12:59 AM »
Check your config under tools it should be the tool on the m6 line is th tool in use

There are two radio buttons use rage wrong one and it expects your guide to pre load the tool first


142
Mach4 General Discussion / Re: Mach 4 and ATC
« on: December 31, 2018, 04:43:07 AM »
Did you email them or raise a ticket

The ticket system is the fastest way

143
General Mach Discussion / Re: maximum work area
« on: December 28, 2018, 12:36:39 PM »
Do you have a valid license for your mach3

144
Mach4 General Discussion / Re: Mach 4 industrial demo not working
« on: December 27, 2018, 02:24:44 AM »
Don’t know yet . It was evening meal time when I got the reply with the fix , when it’s day light and I have woken up I am going to give it a go


145
Mach4 General Discussion / Re: Mach 4 industrial demo not working
« on: December 26, 2018, 02:50:06 PM »
Had a reply looks like they have a fix , I will try it out grats to Bryanna

146
Mach4 General Discussion / Re: Tuning Counts per Unit
« on: December 24, 2018, 03:56:24 AM »
First thing is the mach4 post from fusion is wrong for cutter comp

Both d and p are valid for mach4 but
The post uses p and all it does is to divide the cutter dia by 0.5 hence NBG

You need to modifiythe post to use D correctly ie. change the p *********xx to d *********xx

It’s a few lines to give you the pos and neg cutter comp


Have a look at the Fanuc post do a look up for the d******************


due to this stupid forum software rename the file to mach4.cps.  and store in your personal post folder
I wil try top post again  >:D



I have a modded post that works I will upload when I am on the desktop

147
Mach4 General Discussion / Mach 4 industrial demo not working
« on: December 21, 2018, 02:33:28 AM »
Hi
Let me explain the problem
I am interested in purchasing a lic. For the above note I use mach4 hobby on the mil so I know how to set up and use the platform .
Reasons for the change I could use some of its features for a up coming project .

Now the problem the screen set is flawed
The spindle override do not work at all
The offsets page all the set offsets do not work , the fixture table does not show up nor does the tool table

The table from the menu bar wil not show any data filled in from the offsets page

Edit shows a empty tab this just needs filling in with the screen editor

But this is a 1400 dollar program and it’s on the site try before you buy but it don’t work so how can I test it out

As a test I dropped on the screen from my hobby setup and it worked ok

The faults in the industrial are in the release and the newest in the ftp


I have emailed Newfangled about this but as yet I have not had a reply yet

Stuart


148
Naw as I said it’s


‘K’ for not working

Same word as they call the man to collect dead horses

149
Mach4 General Discussion / Re: Hybrid Stepper Setup in M4
« on: December 10, 2018, 02:07:12 AM »
Well done glad you have it sorted hope it keeps going like you need

Sorry for me getting it wrong with a mechanical problem

150
Don’t worry guys it’s the same for us all , it ‘K’ for not working

You would think the prop,e at ArtSoft would have put up a sticky to inform the great unwashed and to prevent people getting the knickers in a twist


Although there have been lots of posts about this you could have just scrolled down a few pages and seen a result

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 »