Messages

51

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 18, 2015, 04:44:57 AM »

You right about ATM axis, it index the tool nr 1 at homing, the drive is on attach.
Regarding the ModBus set -up I try it , but it seems don't work....or I do somethingh wrong?

52

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 17, 2015, 01:16:51 PM »

Hi All
Got some news:
1-I mount the machine on force power -380V
2-test and move all Axis X,Y,Z except the C for ATM, the old config of this C Axis was trough the RS 232 from the old cnc (I intend to use for this one encoder direct- need the drive one new set-up fotr this ? wait your opinion about)
for time I made all of this without to mount the csmio or Mach, is made direct from the cabinet Inputs/Outputs
3-test the Emergency Chain : mushrooms buttons, limit switches, vacuum chain, pressures, cabinet emergency switches
Unfortunate got no time to test the spindle heads & the inverter
So the point 3. From Thomas rules is not yet accomplished (hope this week to finish with the spindle and test all outputs-mean the secondary, drills , block units for 0 home on corners etc.
I will post some pics with:
Limit switches on Axis C, Z,Y,X and secondary drills location/sense of rotation.
  QUESTION :
When I need to add Input from csmi-o on the Brain controls how I must to declare the csmio address ? see the attach .

53

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 05:00:03 PM »

One more question before sleep :
Any necessary set-up for the CSMIO-Modbus in the Engine Config ...Port and Pin windows ?
see attach
Thank you !

54

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 04:33:30 PM »

@Thomas
About phone I have same opinion ,and use it only for talk or read some short at morning coffe ....
@Hood
The platte is not for cooling; it is made to divide the case on 2 areas (mobo and & power supply area) and to lead the water trough and reach the reservoir on top and pump under area and lead back to radiator on top.

55

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 03:44:18 PM »

Hi Thomas
Got already the I/O extension.
Pff 25 years , that mean you are Daddy's on CNC,
have you some on You Tube or links on your retrofitings ?

Any way I feel pleasure when I do this retrofit (even I headache on manuals) and like to understand each step and all about my machine.

attach explanation
Done some work to my main PC, ....a midplatte for wata' cooling, but it seems glued the sandwich is not the best, I must redo on CNC and use some gasket between plattes.

56

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 03:16:46 PM »

@Hood
Now I'm start to breathe a little, because untill now I fill that I was cabbage on domain....

@Thomas
It seems that your TO DO plan is well organized....if I think from start on all ; then will do a really mess on my mind !

Thanks a lot folks !

57

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 02:49:48 PM »

AHA ! Got it ! for Dinner  
Thanks Hood.
If you find any other simple examples or got some links too, will be very apreciated.
emil
Now is clear for me with I/O for both case .

Is need it Any particular set-up on Engine Configuration window ? see attach

58

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 02:27:52 PM »

Ok here is the IP-A one
http://www.cs-lab.eu/en/upload/fotki/Elementy,%20banery/CSMIO-IP-A%20artyku%C5%82.jpg

This page has them all including the Enc module.

http://www.cs-lab.eu/en/artykul-128-Digital_and_analog_IOs__configuration__its_easy.html

Hood

Thanks Hood !
Got already those files for Pin Assingnation on VB, I found if I do (Pins enabling/assignation ) on Mach 3 then they conflicy with Bit addresses from VB Macro-file...After Manual read I believe first must to assign all in Mach3 but now I'm really confused about Mach3 Pin Assignations - need they to be assign or not ? under Mach3 of course...
emil

59

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 02:12:46 PM »

Glad to see Thomas in on this, he is much better at VB than I will ever be

There is info on the CS-Lab site about using the I/O with the inbuild modbus and for that matter using as I/O in Mach as you would do with the PP.
As you have discovered you can not enable the I/O in Ports and Pins then use the Modbus or you will get conflicts, it is one or the other.


BTW did you manage to see if that is a prox on the tool changer? If so did you see where it goes?      

Regarding ModBus, have no info found on manual from csmio and I have no PLC device, about ATM switch I will do some pics on end of this week, thanks for example !

60

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: May 11, 2015, 02:06:41 PM »

Hi,

don't want to stumble into your your converstion wit Hood.


i am "on board" to help you.
we will see who else is comming up.

excuse my bad bavarin english.

Thomas

Hi Thomas
Any help/info is very valuable for me ! from people who have to do with...csmio-ip-a&Mach3 because I'm really STUCK.I just dive in and finish to read the manuals &  
Regarding the English no worry I'm in same trouble....  
I assume you want to writte Bavarian, no worry I understand also Deutsch Sprache. I live near Koblenz almost 2 years & otherwise I'm BMW -Fan.
But now I'm just one old slave from OSAI and need to close this with Mach3 oportunity.
Any way thanks for answer.