Messages

21

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: July 06, 2015, 05:49:25 AM »

Hi All
Sorry for late ....
Mean time I set 2 relays on my spindle and it seems they work well, I will experience also the csmio wiring when got more time
I decided following:
1-to change the ATM from rotary C on stationary along Y axis (because it seems I find not one VB Macro for rotary, and need to extend the Axis with rotary A )
2-to made one A axis with the old C-axis motor and drive.

Those bring me following:
gain for A axis motor + drive, solve the VB since I got one fromcsmio-site.

wait your opinion about those changements

22

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 24, 2015, 06:28:52 AM »

Hi
Mean time I received from Wojtech csmio-tech support, the DS7500 wiring schema+set-up parameters ; wich I believe is one good option...

23

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 23, 2015, 02:27:31 AM »

HI ALL
Sorry Thomas I was busy those days...
1-So I set-up 2 relays on csmio-output M3 & M4 , and it works ! see attach
2-Regarding 'C" drive for ATM Axis, I have no feedback from the drive, unfortunate I can not have the RS 232 converter with me to check the drive sttings trough the WinBass software....it seems that this drive was set-up only to comunicate with RS232 .
Any ideea on how to made the setup ?

PS good news is that I made some test onRough & FINISH see attach

24

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 17, 2015, 11:56:14 PM »

I wire 2 relays to reff+ and to reff- , and set-up 2 output for M3 M4 , the Output manage the relays to feed with 10V the inverter.

25

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 17, 2015, 12:02:23 PM »

Thomas

I use already 2 relays to change the direction but some people said is not OK to use by M4 - to +; but if you say is OK then I will do it.

By VB ATC I'm almost = 0.....First I will wire the C axis-encoder for the ATC and check the drive and the motor.

26

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 17, 2015, 10:19:47 AM »

by the way,

is the spindle changing direction if you swap the analog Input wires ?

When I change the reff wires the spindle change direction.
Can you help me with the tool change VB ?

27

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 16, 2015, 11:05:14 AM »

Regarding "spindle reverse pin 4"
I try but it seems don't work, I think the inverter is in some how pre-programmed .
Another spindle problem is the brake, when goes stop (end of part-programm the HSD motor-spindle do some strange noise and brake abrupt)
how can I can set some delay in brake ?
any way I think I solve the main problem and now is VB for ATM and drill unit.... + FINE TUNNING

PS give me on PM your mail to send you the movies.
I wonder what happen with Hood , ...!? How are you Hood ?

28

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 16, 2015, 05:12:14 AM »

Hi All
Got good news and also some questions :
1-I run one test on cnc (after set the spindle only for CW rotation) it seems to be good (with one mill for hand machine and curved material, without vacuum hold )
2-I don't know why on Y the cnc made mirror (it is perhaps because I revrse Y Axis on home limit set-up) ? I revrse the Y because by Manual-Jog.
Unfortunate here can not post the short movie.

29

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 08, 2015, 10:01:43 AM »

thank's a lot Thomas !
It's no problem with the manual language = "Ich spreche auch Deutsch - Zwei Jahre in Deutschland gelebt, im Koblenz"

30

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 07, 2015, 09:20:44 AM »

got it, thanks. I will look for .