Messages

31

Mach4 General Discussion / Re: Mach 4 scaling and keyboard button mapping

« on: September 08, 2022, 07:56:37 PM »

Right on, and I like the part where you can read the same good book more than once   😊

FYI, the machine I converted was a Shizoka mill master, 28 inch X travel with FANUC servos

32

Mach4 General Discussion / Re: Mach 4 scaling and keyboard button mapping

« on: September 08, 2022, 07:25:52 PM »

Thanks for the reply Craig,

For some reason I thought you sent me a profile that included scaling like in Mach3 two years ago.

I apologize, my memory apparently isn’t very good.

I will end up doing as you are doing with G50 & G51

Again I apologize for my poor memory and thanks again for responding to me.
Chuck

33

Mach4 General Discussion / Re: Mach 4 scaling and keyboard button mapping

« on: September 08, 2022, 11:19:00 AM »

Chuck I sent you what I had in a message from the link on your info avatar so if you don't get an email from me please let me know.

Hi  Craig,
It’s been a while since you sent this to me.

Would it be possible for you to resend your mach4 profile for scaling.

Long story, but I lost it.

pls Send to my email address Chuck767@gmail.com

Thanks,
Chuck

34

Post Processors / Re: Fusion 360 / Autodesk Post Processors.

« on: December 22, 2020, 02:56:13 PM »

Contact fusion 360 and see if they will do it.

35

Post Processors / Re: Fusion 360 / Autodesk Post Processors.

« on: December 22, 2020, 12:28:02 PM »

MACH 4 uses M 62P1 and M 63P1 for laser control. MACH3 uses M 10 P1 and M 11 P1.

Within the post processor these need to be changed by somebody that’s familiar with the post processor language.

36

Post Processors / Re: Fusion 360 / Autodesk Post Processors.

« on: December 22, 2020, 11:32:31 AM »

Seth at liberty machine wrote the MACH3 laser post processor.

Since the M codes are different for laser on and off in MACH4,  those changes would need to be reflected in the post processor.

37

Mach4 General Discussion / Re: Mach 4 scaling and keyboard button mapping

« on: April 02, 2020, 01:16:00 PM »

Up and running, MACH4 now has the same scaling capabilities as MACH 3

So from my Interest, the subject is closed. 

Thank you,
Chuck

38

Mach4 General Discussion / Re: Mach 4 scaling and keyboard button mapping

« on: March 30, 2020, 12:39:02 PM »

Thank you, I would appreciate that.

With all the projects I have in work, there’s no hurry.

Regards,
Chuck
Stay safe

39

Mach4 General Discussion / Re: Mach 4 scaling and keyboard button mapping

« on: March 30, 2020, 11:02:25 AM »

Thank you for the reply.

I totally understand having to reacquaint yourself with Modifications you’ve done after A period of time.

Would it be possible for you to send your MACH 4 profile?

Since you have it working on your machine, maybe I could modify your profile to fit my machine?


Thank you,
Chuck
 

40

Mach4 General Discussion / Re: Mach 4 scaling and keyboard button mapping

« on: March 29, 2020, 10:50:00 AM »

Hi,

What would it take for me to have MACH4 Feel like MACH 3

Probably not that much....but why? —————-Craig

Craig,
Thanks for the response.
 I understand what you’re saying about MACH4 being so much better Then MACH 3

In my shop, I frequently use the X and Y axis percent scale feature within MACH 3 quite often.

I have MACH 3 on three different machines and will be converting 2 of them to MACH4 and would really like to have the same feature for scale on all three machines. 

So I’m really interested in what it would take to make my MACH4 machines do the Axis  scaling like MACH 3.

Thanks,
Chuck