Hello Guest it is November 17, 2019, 07:14:57 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - chuck767

Pages: 1
1
General Mach Discussion / Need help on MPG
« on: July 02, 2019, 12:55:29 AM »
I have 3 licensed version Of MACH3 On 3 different machines.

The first machine has a complete Machmotion controls upgrade That includes an MPG with axes and movement increment selector switches. It works great and I want to install the same type of MPG setup on the second machine.


For some reason on this second machine, I can't get the MPG to work.  The MPG Is being controlled Via an M36 board From CNC 4 PC.

My problem appears to be due to the fact that when I use the tab key To activate The fly out MPG panel, I cannot get The MPG yellow light to come on When I click The "jog mode" buttons. I can get the continuous and step Lights to come on but not the MPG.

The third machine does not have an MPG wheel, But With the tabbed out MPG panel, I can get All 3 Lights to come on when hitting the "jog mode" button, IE Continuous, step and MPG.

Does anyone know Why I cannot yet The MPG Light to work On the second machine?


Thanks,
Chuck

2
Post Processors / Laser postprocessor
« on: May 13, 2019, 09:45:39 AM »
I would like to Attach a postprocessor Written by Seth At Liberty machines, Inc

It can be used for laser, waterjet, or plasma 

I tried the arc soft Plasma Postprocessor And it did not work for what I was doing. Seth agreed to write one and it works great.

I cannot attach it because it is a  .CPS file

Could somebody pls tell me where I can Get this post-processing File Recognized?

Thanks,
Chuck

3
General Mach Discussion / post processor
« on: May 13, 2019, 01:57:15 AM »
Where can I post a Postprocessor for Fusion 360 Laser Cutting?

Somewhere I saw a place For posting postprocessors But I cannot find it now.

Chuck

4
General Mach Discussion / Mach3 laser
« on: November 28, 2018, 03:17:38 PM »
I am using Fusion 360 “Laser cutting” CAM options.

When I try to post process the normal MACH3 mill does not work properly.

After some researching found information that shows ARTSOFT
Has a Fusion 360 post processor for MACH3 Laser.

What does it take to get this postprocessor included in the Fusion 360 postprocessor list?

Thanks,
Chuck

5
General Mach Discussion / cutting a spiral
« on: September 14, 2018, 11:02:34 PM »
I'm trying to mill a spiral. anyone know the code? I found a G2.1 code but Mach3 doesn't like it.
Thanks,
Chuck

6
General Mach Discussion / Setting up 4th axis
« on: April 29, 2017, 01:14:02 PM »
 I am putting a fourth axis on my table top, deep groove, milling machine

 It was working but I wanted to fine-tune the movement of the motor  and ended up changing something to the point where all the motor does now is vibrate when I try to move it.

 I have tried everything I can think of but I cannot get the motor to rotate the way it did previously.

 The motor is a pacific scientific.  5 V DC motor with 1.8° per step, 200 steps per revolution

 Any ideas as to what I have inadvertently changed would be appreciated.

 Thanks, Chuck

7
General Mach Discussion / starting a lubrication pump
« on: March 11, 2017, 08:01:56 PM »
Hi Group,
I'm looking for some help on how to send a signal that would start my spindle lubrication pump as soon as the spindles starts spinning.

This signal would energize a relay than would start a single phase 115vac KB Electronics VFD that generates 3 phase power for the spindle lub pump.
 
I'm running Mach3, ESS Motion control board and a C32s breakout board from CNC4PC.

I would think this is relatively straightforward for an experienced user, but unfortunately I'm still a novice. 

Thanks for your help,
Chuck

Pages: 1