Messages

21

General Mach Discussion / Threading Wizard

« on: July 13, 2017, 12:00:52 PM »

Hi
I tried the threading vizzard for the first time but it just stoppe at line 7. The spindel was still running but nothing happen. Its M16x1.
What di I do wrong?

Here are the code:
G0 G40 G18 G80 G50 G90
G00 X16.025
G00 Z1.1
G00 X16
M03 S300
M08
G76 X15 Z10 Q1 P1 J0.006 L45 H0.3 I29 C0.025 B0.0001 T0
M9
M5
M30

Gaute

22

General Mach Discussion / Mach3 turn

« on: March 26, 2017, 07:41:29 AM »

Hi
Anyone that can helpe me with this set of codes?
Im going to turn a collet that I draw in Fusion360 posted from there.
When I simulate it in Fusion360 COM it seems to be perfect but after a few cut the x axis just go into the steel and cut it right down with big blue chip.
I´m not sure which line it happen as I just hit the emergency stop.
I have run the CNC late with just simple G codes not generated G codes from fusion before.

%
(ROUTER COOLET)
N10 G90 G94 G18
N11 G21
N12 G91
N13 G90

(PROFILE1)
N14 T0202
N15 G54
N16 G95
N17 G96 S70 M3
N18 G0 X36. Z1.404
N19 G0 X18.581
N20 G1 X17.828 F1.
N21 X15. Z-0.01
N22 Z-19.5 F0.1
N23 X15.98
N24 X18.808 Z-18.086 F1.
N25 G0 Z1.404
N26 X17.293
N27 G1 X14.465 Z-0.01 F1.
N28 Z-19.5 F0.1
N29 X15.
N30 X17.828 Z-18.086 F1.
N31 G0 Z1.404
N32 X16.799
N33 G1 X16.772 F1.
N34 X13.944 Z-0.01
N35 G18 G3 X14.371 Z-0.805 I-0.982 K-0.69 F0.1
N36 G1 X14.091 Z-2.405
N37 G3 X14.064 Z-2.508 I-1.195 K0.105
N38 G1 X13.465 Z-4.207
N39 Z-19.5
N40 X14.465
N41 X17.293 Z-18.086 F1.
N42 G0 Z-2.792
N43 G1 X16.293 F1.
N44 X13.465 Z-4.207
N45 X13.101 Z-5.239 F0.1
N46 G3 X12.816 Z-5.63 I-1.182 K0.208
N47 G1 X12.482 Z-5.919
N48 Z-19.5
N49 X13.465
N50 X16.293 Z-18.086 F1.
N51 G0 Z-4.505
N52 G1 X15.311 F1.
N53 X12.482 Z-5.919
N54 X11.5 Z-6.77 F0.1
N55 Z-16.517
N56 G3 X12. Z-17.25 I-0.95 K-0.733
N57 G1 Z-19.5
N58 X12.482
N59 X15.311 Z-18.086 F1.
N60 G0 Z1.404
N61 X13.262
N62 G1 X12.428 F1.
N63 X-0.4 Z-0.01
N64 Z-0.5 F0.1
N65 X11.98
N66 G3 X12.378 Z-0.717 K-0.2
N67 G1 X12.098 Z-2.317
N68 G3 X12.094 Z-2.335 I-0.199 K0.017
N69 G1 X11.131 Z-5.065
N70 G3 X11.084 Z-5.13 I-0.197 K0.035
N71 G1 X9.5 Z-6.502
N72 Z-17.05
N73 X9.6
N74 G3 X10. Z-17.25 K-0.2
N75 G1 Z-19.5
N76 X12.828 Z-18.086 F1.
N77 X14.
N78 G0 X36.

N79 G91 G28 X0. Z0.
N80 G90
N81 M30
%
Gaute

23

General Mach Discussion / Re: Homing

« on: March 22, 2017, 04:25:55 PM »

Thaks, Craig

24

General Mach Discussion / Homing

« on: March 22, 2017, 04:01:16 AM »

Hi
I'm working on job on the CNC router that will take about 8 hours. I have only a couple of hours available now and then.
I stop the machine and note down the line number, than put the machines three axis in 0 by G0 X0 Y0 Z0, shut off the PC and the control. When I start up again I just verify that the machines axis are all in 0 than load the program, find the correct line and hit Run From Here.
This works perfectly.

Normally when I start up I home the machine, then 0 the axis on the stock.

My question is; can I always just leave the machine in 0 (PC and control off) and start up again without homing just 0 the axis?

Gaute

25

General Mach Discussion / Re: Router stopped less than midways

« on: March 15, 2017, 02:34:32 PM »

Hi
All my motor cable was screened but the screen was not earthed. I have now terminated them to earth and run the router for some hours without tripping. I have also used run from here several times with perfect result.
Thanks a lot Craig
Gaute

26

General Mach Discussion / Re: Router stopped less than midways

« on: March 13, 2017, 09:46:51 AM »

Hi,
Thanks a lot. Will try and isolate or eliminate the noise source.

Will try some run from here in the air first.

27

General Mach Discussion / Router stopped less than midways

« on: March 12, 2017, 08:59:30 AM »

Hi
I was cutting with my cnc router and Mach3 for about one houre than it stopped besause a limit witch triggered, non of the switches was triggerd. I belive the program is app 3000 lines and I had just over 1000 lines done.
This limit switch triggerd for no reason I know about, it has happend ones before. When I reset it seems to be ok.
I it possible to restart the process at line 1000? I shut the PC and control off but I know exactly where 0 are on all the three axis. Or can I just delete 900 lines, of cause leave the start up lines and start from there?
Hope someone can give me some advises

28

General Mach Discussion / Re: How do I home the ATC

« on: February 26, 2017, 02:25:06 AM »

Thank you Tweakie
Will this work?
'ATC Home

Code("M7")         'Unlock tool changer turret
Sleep(1000)               'Wait to unlock

SingleVerify(3)         'Home A axis, 3 = A axis
 
Sleep(20000)         'Wait for some time

Code("M9")       'Lock tool changer turret
Sleep(1000)               'Allow to lock


Then I put it into the macro folder, but how do I assigne a G code or buttom?
Gaute

29

General Mach Discussion / How do I home the ATC

« on: February 25, 2017, 05:17:04 AM »

Hi
How do I home my ATC?
It is an 8 tool ATC for Mach3 Turn.
Activate cylinder is M7
Stepper motor is A
The home switch for A axis motor is set at tool 0.

30

General Mach Discussion / Re: Lathe Wizard question

« on: January 15, 2017, 04:38:33 AM »

- should be towards the chuck, sorry.