Messages

11

General Mach Discussion / Can someone verify my wiring please?

« on: October 20, 2015, 06:16:54 AM »

Can someone verify my wiring please?
I have a PMDX-122  and M542 drivers motors

Thanks so much!

12

General Mach Discussion / Re: Slave axis & Kernal speed PROBLEM! Need help please!

« on: October 17, 2015, 03:05:37 PM »

Hello Rob,

First of all thanks about your reply and help with me!
I have a good news about my machine! I have founded the problem that is was the pulsewidth, I have changed it to be 5, its was 2
All times I was with old pc and win xp, this time I have changed to a new pc with win 7 32 bit!

13

General Mach Discussion / Slave axis & Kernal speed PROBLEM! Need help please!

« on: October 17, 2015, 02:53:38 AM »

Hello people,

I have win 7 32 bit with tb6600 board and nema 24.
I have a problem when I slave A to Y, one of the motors run ok and smoothly but the ather motor run slowly with intermittent steps!
I have changed the motors but its still one of them moving bad!
I have tried to change my kernal speed and sometimes its going ok but when restart my Mach3, again the problem appear!! I didn't know what to do! Can someone please help me?

Thanks so much!

14

General Mach Discussion / Re: Mach3 issues on Windows Xp! Please help!

« on: April 23, 2015, 01:07:46 AM »

Ok guys, thanks you so much
I will update you soon

15

General Mach Discussion / Re: Mach3 issues on Windows Xp! Please help!

« on: April 22, 2015, 04:33:35 PM »

Bar553, did you mean the updates of Windows?
Stirling, excuse me man but I didn't understood you! But I didn't switched yet to a licensed version, now I thinking about the SCHP! What you think man?

16

General Mach Discussion / Re: Mach3 issues on Windows Xp! Please help!

« on: April 22, 2015, 12:34:25 AM »

Ok guys thanks you so much for your help, but what about the charge pump? There are no body have asked me anout it!
Are the SCHP help me here? Or have some correlation here?

17

General Mach Discussion / Re: Mach3 issues on Windows Xp! Please help!

« on: April 21, 2015, 10:04:30 AM »

Its not a rocket science! I like it man

18

General Mach Discussion / Re: Mach3 issues on Windows Xp! Please help!

« on: April 20, 2015, 11:07:24 PM »

Really I didn't know what to do! Or to install windows 2000 or to stay on Xp! I didn't know!
My problem is that I have finished my machine and now I need to move it! But I'm conern to make for me problem on the future!

19

General Mach Discussion / Re: Mach3 issues on Windows Xp! Please help!

« on: April 20, 2015, 10:20:14 AM »

So you say do not to change to 2000, just to stay with Xp but with licensed version? Like that I have understood..

20

General Mach Discussion / Re: Mach3 issues on Windows Xp! Please help!

« on: April 20, 2015, 04:32:50 AM »

Hey guys, really thanks for your help about my problem, yeah geh7552 my windows it's not a licensed version I think, but are you sure that I need a licensed version of windows?

Because I think to bay another new PC with windows 2000,
 I didn't know if 2000 will be more effectively than xp, what you say man?

Thanks so much!
Best regards!