Hello Guest it is March 28, 2024, 08:16:56 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - wakedabed

Pages: 1 2 3 4 5 6 7 8 9
1
General Mach Discussion / Re: Motherboards And Mach3, questions..
« on: January 23, 2017, 11:59:45 AM »
Thanks you so much guys, I really appreciate your recommendation and your answers and help!

2
General Mach Discussion / Motherboards And Mach3, questions..
« on: January 23, 2017, 12:35:21 AM »
Hello people,

Can someone explain to us what the difference will be between one motherboard 2Gh and another motherboard 4Gh? We talking about the same pc with win7 32-bit..
How mach3 will react with the two motherboards?

Thanks so much!

3
General Mach Discussion / In Reverse Run HELP!
« on: December 13, 2016, 02:36:42 AM »
hello people,
i want to ask if there are some led for g00??
because, when i want to reverse run the g-code (that contain lines start with g00/g01/g02/g03), and when i press STOP (do while running in reverse), if the line that i stopped was g00 to activate the specific led, and if its was something else to inactivate the specific led?

4
General Mach Discussion / Re: ArcOK signal purpose please!!
« on: July 18, 2016, 04:23:37 PM »
First of all thanks about your reply and hlep.
I have a cnc plasma with proma thc 150 compact, I dont have wire connected from arcok signal on the thc to the c11 breakout board, but in the inputs table I have put arcok signal to port 1 and pin number 12 (free input) and I have put it to active hight (to be on all the time).
My thc work very well, up and dn very good, pierce time and pierce height ok, BUT if suddenly the material touch the torch immediately on the thc screen it show (---) and then the torch do not up or dn JUST if the material somehow leave the torch then resume to up and dn...
What you think man? Please to help me
I have Hypertherm 125A

5
General Mach Discussion / ArcOK signal purpose please!!
« on: July 18, 2016, 04:00:52 PM »
Hello there,

Can someone tell what is the purpose of arcok signal?

I have a THC proma

6
Yes I know this way to see which G0? It will be the next, but I need something else, I need when I press reverse run and the machine running in reverse I want to make a led on the screen that if the machine is in G00 to be on this led, else to be off, because I need to use this led to something

7
Hello people,
I want to ask how this message work? How I can know the mechanism of this? I can put on my screen a LED that show me if my machine in G00 or in G01???? PLEASE HELP!!!

8
Hello people,

I have a C11GSD breakout board from cnc4pc and cap04 thc, on the breakout board I have 3 relays, I use just the first 2 relays, one for plasma and the second for flame.
When I write dooembutton(110) on my macro its ok the relay and the thc are working, but when I try to write Activate signal(output2) for the second relay, the thc not working!

Please help!

9
Hello people,

I have a C11GSD breakout board from cnc4pc, and now I trying to activate my CAP04 THC plasma, on the mach3 I can see the led of up and down fladhing but no movement of the z axis!
Can someone please help me with this problem?

Thanks so much!

10
General Mach Discussion / Re: Can someone verify my wiring please?
« on: October 25, 2015, 01:39:29 PM »
Thanks so much man ;)

Pages: 1 2 3 4 5 6 7 8 9