Hello Guest it is December 08, 2019, 01:25:19 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - eCraft

Pages: 1
1
PoKeys / Re: Firmware problems 57E
« on: October 23, 2014, 12:39:47 PM »
Hello Matevž

Meanwhile i took a 74HC595 ic to solder the easy port-expander from the manual of the pulse engine.
Trying this i had the problem, that i couldn´t jog my Z-Axis properly (it jogs only a few mm).
So I did all the steps you told me, and with a clean installation of mach3, and only setting the motor-parameter i could jog all 3 axis.
Now i did one change after the other on the config to look what i did wrong the last times.
Jogging my z-axis wasn´t possible after setting the software limit to +8. So i tried setting it to +10, changed the position of my home-switch and everything works :D

I took my backup, set my limit of the z-axis to +10 instead of +8 and my machine was useable again.

Now (hopefully) my last problem is my auto-tool-zero script. There is a problem with the G31 command - i always get a "probe error - overrun" after executing this command. And my Axis only moves 0.02 mm.
But I hope I´ll get this working, too.

Kind regards,
Josef

2
PoKeys / Re: Firmware problems 57E
« on: October 22, 2014, 08:10:16 AM »
Hi Matevz

did you get my e-mail I sent you 2 days ago? or is it lost in your spam-folders cause of the .xml attachements?
i hope you can help me.

I´m running Mach3 version R3.043.066. Is there a newer one, i couldn´t find on the website?

Regards,
Josef

3
PoKeys / Firmware problems 57E
« on: October 18, 2014, 04:49:29 AM »
Hello

for a few days i try to get my Pokeys57E working with my mill for step/dir generation.
I´m using the latest Mach3 full version on a new installed 32 bit pc running Windows XP.
The Pokeys is directly connected to the PC. My breakoutboard is from benezan-electronics and my drives are diy servodrives.
My drivers worked properly connected to the printer port, but sometimes Mach3 lost a few steps.

So i decided to switch to Pokeys and the integrated 3ch pulse engine.
But i had a few problems:

Using the latest version (3.1.38) my motors start moving when i start mach3. I can jog my axis with the keyboard, but Pokeys always wants to drive all 3 axis in one direction, even if the RESET Button in mach3 is pushed and the charge-pump function of my BOB is disabled - otherwise charge-pump function works fine.
Shutting Mach3 stops my motors spinning. Using the testfunction in the Pokeys Software everything is fine.

Then i went back to version 3.1.17 .
Here i got the problem that jogging by keyboard/gamepad, or starting the automatic homing function, is very slow (about 0.1% of my choosen max. speed). If i home the axis manually and jog my machine using g-code commands - the used speed is as fast as i choose in my gcode. I tried different changes, but without success.

At least i installed version 3.0.65
With this version jogging works well, but when i start automatic homing, the procedure is started and looks like everything works, but mach3 doesn´t recognize that my axis are homed. Ok i set my axis manually and tried a piece of testcode, then i saw that i got missing steps. (it has to be a controller-problem cause i use servo drives). And the charge-pump doesent work.


Hope someone can help me with my problems or give me tipps solving my problems with Pokeys.
Meanwhile i have to switch back to the printerport -.-


Greetings from Germany,
Josef

Pages: 1