Messages

11

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: November 19, 2014, 02:57:55 AM »

i didn't get a message on the error line. And i have set the home singnals on the Darwin motor setup page. I have assigned each homing signal to the correspondig motor.
maybe I have to switch the logic level of the homing signals - i will check that...

12

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: November 18, 2014, 12:35:29 PM »

Hi,

i have installed the released MACH4 and the Darwin Plugin (with licenses) and configured the system as described in the youtube video.
Jogging works fine...
But when I press the Homing Button, nothing happens!

This is the log after pressing the homing button:

2014-11-18 18:20:55.281 - API: mcAxisHomeAll() called.
2014-11-18 18:20:55.281 - Attempt transition from "Idle" on event "Home" Command.cpp:851
2014-11-18 18:20:55.281 - S_IDLE_on_exit
2014-11-18 18:20:55.281 - MACH_STATE_start_homing
2014-11-18 18:20:55.281 - S_HOMING_on_entry
2014-11-18 18:20:55.281 - Signal id 1131, (Z Homed), changed from HIGH to LOW.
2014-11-18 18:20:55.296 - Signal id 1129, (X Homed), changed from HIGH to LOW.
2014-11-18 18:20:55.312 - API: mcAxisHomeComplete() called. axis 2
2014-11-18 18:20:55.312 - Signal id 1131, (Z Homed), changed from LOW to HIGH.
2014-11-18 18:20:55.312 - All motors marked as still.
2014-11-18 18:20:55.312 - API: mcMotionSync() called.
2014-11-18 18:20:55.312 - SyncPosition()!
2014-11-18 18:20:55.406 - Signal id 1130, (Y Homed), changed from HIGH to LOW.
2014-11-18 18:20:55.421 - API: mcAxisHomeComplete() called. axis 0
2014-11-18 18:20:55.421 - Signal id 1129, (X Homed), changed from LOW to HIGH.
2014-11-18 18:20:55.421 - All motors marked as still.
2014-11-18 18:20:55.421 - API: mcMotionSync() called.
2014-11-18 18:20:55.421 - SyncPosition()!
2014-11-18 18:20:55.515 - Signal id 1132, (A Homed), changed from HIGH to LOW.
2014-11-18 18:20:55.531 - API: mcAxisHomeComplete() called. axis 1
2014-11-18 18:20:55.531 - Signal id 1130, (Y Homed), changed from LOW to HIGH.
2014-11-18 18:20:55.531 - All motors marked as still.
2014-11-18 18:20:55.531 - API: mcMotionSync() called.
2014-11-18 18:20:55.531 - SyncPosition()!
2014-11-18 18:20:55.640 - API: mcAxisHomeComplete() called. axis 3
2014-11-18 18:20:55.640 - Signal id 1132, (A Homed), changed from LOW to HIGH.
2014-11-18 18:20:55.640 - Attempt transition from "Homing" on event "Stop Home" Command.cpp:954
2014-11-18 18:20:55.640 - S_HOMING_on_exit
2014-11-18 18:20:55.640 - MACH_STATE_stop_homing
2014-11-18 18:20:55.640 - SyncPosition()!
2014-11-18 18:20:55.640 - S_IDLE_on_entry
2014-11-18 18:20:55.640 - All motors marked as still.
2014-11-18 18:20:55.640 - API: mcMotionSync() called.
2014-11-18 18:20:55.640 - SyncPosition()!


what goes wrong?
Does anybody have an idea?

Stefan

13

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: July 21, 2014, 06:20:14 PM »

Tested Mach4 1900 with Darwin driver today.
I have configured the darwin plugin as described in the youttube video...

I was able to jog all three axes, but I wasn't able to do a homing with the homing button.
Do I have to configure anything else?