Messages

81

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 18, 2018, 07:04:13 AM »

Allan Craig

Thanks for expanding on this. Am I right in thinking we are talking about GND Pins on the CSMIO not being used, the potential issue. Eg pins 17,21,25 on the encoder inputs?

Would this be something Cs Labs could help with or maybe Schneider Technical? The issue with talking to Schneider technical would be my lack of knowledge in circuits .   

 

Cheers
Mick

82

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 17, 2018, 04:43:59 PM »

Hi Allan

Great news, thanks for taking the time again and proving a rapid clear answer. I will be using the pre-wired sub d 50 CN1 cables. I did order them but haven't arrived yet .  Will get the motors and drives fitted over the weekend and delve into the operating manual.  

Cheers
Mick

83

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 17, 2018, 03:12:41 PM »

Hi Allan

Thanks for coming back in. The motor and drive links are below. I cant attached the manual the file is too large so I have sent a link to it.

https://www.schneider-electric.co.uk/en/product/LXM28AU07M3X/motion-servo-drive---lexium-28---single-and-three-phase-200...230-v---750-w/

https://www.schneider-electric.com/en/product/BCH2LF0733CA5C/servo-motor-bch---80mm---750w---w-oil-seal---w-key---leads-con/

https://download.schneider-electric.com/files?p_enDocType=User+guide&p_File_Name=LXM28A_Manual_V2.1_EN.pdf&p_Doc_Ref=0198441114054-EN&_ga=2.266361352.789260454.1534532339-227965827.1533213090

Cheers
Mick

84

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 17, 2018, 11:05:15 AM »

Hi Allen
Not sure what they are yet. Only got them yesterday and have had chance for a full read. Would you mind taking a look at the manual.

Cheers
Mick

85

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 17, 2018, 01:24:28 AM »

Hi Craig

Thanks. Will have more time to read up over the weekend.

Mick 

86

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 16, 2018, 04:51:27 PM »

Am I right in thinking it doesn't need the GND and 5VDC from the controller??

Cheers

87

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 16, 2018, 04:31:18 PM »

Hi
Like I said lots of reading to do. Lol
Ignore the last post I think the output to the controller is on CN1 50 pin plug.

It appears to be on CN1 plug pins 21,22,23,24,25,50 you have A+ A- B+ B- Z+ Z-

Not sure where the GND and 5VDC are coming from though at the moment.

Cheers

88

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 16, 2018, 03:22:10 PM »

Hi Craig
The encoder does wire straight to the drive. The output to the controller only has four wires. T+ T- Gnd 5vdc. I may be mis understanding the wiring info. Lots of info.

Mick

89

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 16, 2018, 02:58:38 PM »

Cheers Craig.
I don't doubt the motors at all after all the discussions .
Just trying to get my head around the encoder wiring to the controller at the moment. It seems I only have T+ T- GND and 5Vdc.
Loads of reading to do.

90

General Mach Discussion / Re: CS Labs CSMIO/P-A

« on: August 16, 2018, 01:20:49 PM »

Drives and Servos arrived. Bit concerned they are half the size if the old Dc Motors. Modern technology I hope. Lol