Hello Guest it is July 18, 2019, 10:27:03 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - giannis121

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 »
51
VB and the development of wizards / Wait until external application ends...
« on: November 12, 2010, 04:51:54 AM »
I'm using a button to call an external application:
Shell ("c:\myapplication.exe")

Inside the same button i want to load a file after "myapplication" file is closed.
LoadFile("c:\myfile.txt") 

So, i need something like "~wait for myapplication to close" between these commands:
Shell ("c:\myapplication.exe")
"Wait for myapplication to close"
LoadFile("c:\myfile.txt")

How can i do that?


52
General Mach Discussion / Re: Reverse Run stop when G0 ...
« on: October 12, 2010, 11:51:38 AM »
Its exaclty the same, while i am cutting straight big lines.

53
General Mach Discussion / Status error messages list.
« on: October 12, 2010, 03:32:02 AM »
Does anyone know where i can find a full list of the status error messages?

Giannis

54
General Mach Discussion / Re: Reverse Run stop when G0 ...
« on: October 11, 2010, 09:01:01 AM »
BR, this works, but when the distance between holes is small the program doesn't stop at G0. The pause is not responding fast.
My will is to stop exactly on the G0 command.

I tried to use DRO 819 (which is "motion mode" and works good when forward), but doesn't work at all when reverse running.

Let me know if you can think of anything else.

Giannis

55
General Mach Discussion / Re: Reverse Run stop when G0 ...
« on: October 08, 2010, 07:00:00 AM »
Just one more question please.

Is there any variable changed when the program goes from G1 to G0 etc...
If so, i can make a brain looking at the revense run button and this variable and press pause when needed. (?)

Giannis

56
General Mach Discussion / Reverse Run stop when G0 ...
« on: October 08, 2010, 05:25:16 AM »
Hello everyone!

When i lose the cutting, i press pause and reverse run, in order to go back to the path. This works fine.
The revense run will go back the whole program until reaching to the line No 0 (zero).

Is there any way to do the following: (?)
When pressing reverse run the program will go back until finding the G0 command and then pause or stop.

How can i do that?
Any ideas?

Giannis

57
General Mach Discussion / Re: What Do You Think?
« on: October 07, 2010, 05:56:33 AM »
Windows 7 work very good with Mach on my machine!

58
General Mach Discussion / Re: Jog Z axis when in program... (?)
« on: September 08, 2010, 12:56:59 PM »
OK
I found (after long time) a topic that suits my question.
http://www.machsupport.com/forum/index.php/topic,2656.0.html

59
General Mach Discussion / Re: Jog Z axis when in program... (?)
« on: September 08, 2010, 12:17:28 PM »
Thank you for the quick reply.
This will activate just an output.
My Z axis is pulse controlled by mach.

60
General Mach Discussion / Jog Z axis when in program... (?)
« on: September 08, 2010, 11:57:52 AM »
Possible while the machine is running a program, to move the Z axis with a button?
I use the mach for cutting with waterjet.
Sometimes i need to move Z axis up or down manualy, while running.
Any ideas?
Thank you.

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 »