Hello Guest it is December 06, 2021, 01:35:51 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Ghantos

Pages: « 1 2 3 4 5 6 »
31
CS-Lab / Re: Csmio/IP-A drives
« on: March 26, 2015, 06:13:54 AM »
Yes hood it's bidirectional 5v square wave.
Regards ,
Basim

32
CS-Lab / Re: Csmio/IP-A drives
« on: March 26, 2015, 02:34:12 AM »
dear Hood;
 my machine that i need to retrofit has Bosch CC100 controller.
it has  DC servo Dirves Bosch of SM- 10/20
servo motors has Encoder that connected to the CNC controller Not to the Servo Drive.

with DSPMC of vital no problem, i think they have the same property so i also think that it should not be a problem.

please let me know

Ghantos

33
CS-Lab / Re: Csmio/IP-A drives
« on: March 25, 2015, 05:10:59 PM »
Dear hood ,
My machine has a servo DC motors with tachometer.
 
Now, I Ask if the csmio-A supports this kind of servos

And if the setting the PID of this servo is different than the ac servo.

Today I got the kit and I want to start with the axes.
Regards,
Ghantos

34
CS-Lab / Re: Csmio/IP-A drives
« on: March 14, 2015, 04:03:39 PM »
Dear hood and all friends,
Thank you a lot at this time.
I hope to get the controller soon and start to analyse the job.
Regards,
Ghantos

35
CS-Lab / Re: Csmio/IP-A drives
« on: March 14, 2015, 01:46:27 PM »
Thanks Hood and Thomas ,
Really I ask a lot because up to now I did not get the controller to start the project.

And I want yo get as much as I can information yo ease the getting started with hje job.

Q:
What is the "step per" in mach and the encoder counts in the plugin !

Should both be the same?

Regards,
Ghantos

36
CS-Lab / Re: Csmio/IP-A drives
« on: March 14, 2015, 04:44:42 AM »
Thanks a lot !
I know that, but my question where to map the input for the homing ?
Is it in mach3?

From your experience , which controller better
Dspmc of vital or the csmio-a from CS-lab??

Please let me know
Basim

37
CS-Lab / Re: Csmio/IP-A drives
« on: March 14, 2015, 03:14:59 AM »
Thank you hood
But what do you mean by "tell the plug in"
Do you mean in mach3 ports and pins?

I see in the manual that when we activate the index homing the pin become "dead" not active.
Please let me know
Regards
Ghantos

38
CS-Lab / Re: Csmio/IP-A drives
« on: March 13, 2015, 03:59:27 PM »
Hi friends,
Regarding the CSMIO-A , what is the function and the usage of the index homing!
What about the pin out mapping for this?

I noted at the user manual that when we use the index homing the pin become "dead" not active?
Could you please explain?

Sorry but this is my first retrofitting project and I have no good experience   

Regards,
Ghantos

39
CS-Lab / Re: Csmio/IP-A drives
« on: March 09, 2015, 10:13:09 AM »
hello hood;
I want to retrofit a machine with CSMIO/P-A.

I have some questions:

how to read a specific Input using the GETOEMLED or GETUserLET??
how I can activate a digital Output??
is it the same like the dspmc ip of vital??
I know that vital already mapped the oemled to match their plugin, so how I can do this in the CSMIO??

if my VFD is +/-10V how I can set it up ??
thank you
Ghantos

40
Brains Development / Re: Spindle Contactor Brain, with Delay.........
« on: October 15, 2014, 01:00:28 PM »
Hello Scott
Thank you for the reply!

Maybe I did not explain the problem well.

What I need is to Check if I get the input 2 within maximum  3 seconds after the output 1.
It mean if I get input 2 after 2 seconds for me it's ok!!

The 3 seconds it's the timeout for the input.

Your brain and macro pump seems checking if the input 2 came exactly after 3 seconds.
Please let me know your suggestion.
Regards ,
Ghantos

Pages: « 1 2 3 4 5 6 »