Hello Guest it is November 27, 2021, 06:59:58 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - babo18

Pages: 1 2 »
1
General Mach Discussion / Mach3 Stepper Motor Grinding
« on: January 08, 2021, 06:43:38 PM »
Hi,
I am having a problem recently with my stepper motors grinding and missing steps while running programs. I have been running my cnc router for quite some time on Mach 3. I recently relocated the machine and have since been having issues with it. I can jog the machine in addition to using the "go to zero" function with no problems, the motors run smooth. The problem starts when I load and run a program. The motors on all three axis grind horribly and skip steps. The weird thing is that if I press "stop program" and then hit "cycle start" again, the motors run perfectly as if nothing happened. If I stop the program and do a "run from here" or restart the program completely, the grinding comes back, and can only be fixed by the "stop" "start" button presses. The fact that I can jog the motors just fine suggests to me that its not a mechanical or electrical issue. I have also tried different microstepping on the motors with no luck. I believe this to be a Mach problem, but I am lost as to why it is acting up now after I have been the setup for years. Any suggestions?

Thanks!
Matt

2
General Mach Discussion / Re: Homing issue.
« on: August 09, 2013, 10:20:23 AM »
This is the only other file I could find.

Phill

3
General Mach Discussion / Re: Homing issue.
« on: August 09, 2013, 07:45:18 AM »
Here is the file. I think this is the one you want.

4
General Mach Discussion / Re: Homing issue.
« on: August 08, 2013, 09:58:40 PM »
When I attach the XML file to the reply it gives me an error message of duplicate file already uploaded.

5
General Mach Discussion / Homing issue.
« on: August 08, 2013, 02:39:12 PM »
Hello,
     I am having problems trying to home two of the three axis on my cnc. The y axis will home itself, touching the switch and backing off until it releases the switch. The issue is that x and z automatically zero after the y axis home is touched. I am using three seperare homing switches that are not connected in any way. Any ideas of what is causing this?

Thank you,
Phill

6
General Mach Discussion / Re: Mirrored image issue
« on: August 07, 2013, 04:06:46 PM »
Thank You!

Phill

7
General Mach Discussion / Re: Mirrored image issue
« on: August 07, 2013, 03:16:07 PM »
All the axis move correctly on the Mach 3 screen and cooresponds to the table movements but the final product is upside down from the Mach 3 picture.

Thanks
Phill

8
General Mach Discussion / Mirrored image issue
« on: August 07, 2013, 02:08:15 PM »
Hello,
     I am having issues with milling using Mach 3. I load a CAD file with an image that is normal and upright. When I actually cut the image out, it is upside down (a mirrored image of the origional picture).  If I was to pocket the part, it would pocket the bottom side instead of the top. Any ideas of why this is happening?

Thank You,
Phill

9
FAQs / Re: E-STOP - Help
« on: August 02, 2013, 12:29:58 PM »
Thank You.

10
FAQs / E-STOP - Help
« on: August 02, 2013, 10:30:30 AM »
Can anyone tell me why when I configure an external E-Stop for my machine I get 4 " Port 1 Pins Current State " leds to light up?  When I toggle the E-Stop switch the number 4 led goes on and off but the first 3 leds always remain on. I have no other inputs to mach 3 at this time.
Thanks.

Pages: 1 2 »