Hello Guest it is December 06, 2021, 01:30:19 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Børge

Pages: « 1 2 3 »
11
General Mach Discussion / Re: Mach3 acting funny
« on: September 23, 2013, 04:09:33 PM »
Here we go

12
General Mach Discussion / Re: Mach3 acting funny
« on: September 23, 2013, 03:58:35 PM »
Hi

it wont attach the XML files

Børge

13
General Mach Discussion / Re: Mach3 acting funny
« on: September 23, 2013, 03:47:49 PM »
Here is the code

Code: [Select]
(File vectori3_multipass21.tap )
(Sunday, September 22, 2013)
G90G80G49
G90.1
G0 Z0.0522 X0.0507
M3
F91.000 G1 Z0.1029 X5.8799
G1 Z56.9719 X5.8799
G0 Z56.9719 X5.4710
G1 Z0.1537 X5.5218
G0 Z0.0522 X4.5505
G1 Z5.1652 X4.5505
G0 Z4.3983 X3.4256
G1 Z0.0522 X3.4256
G0 Z0.1029 X2.2499
G1 Z3.7851 X2.2499
G0 Z3.4778 X1.4830
G1 Z0.1029 X1.4830
G0 Z0.1768 X0.0542
G3 Z1.6830 X1.0725 I0.0955 K1.2462
G2 Z3.0411 X0.7680 I2.4157 K2.6974
G2 Z3.7229 X1.1674 I1.7357 K2.9270
G3 Z5.8688 X4.9947 I-0.4943 K11.1726
G3 Z6.5703 X5.0148 I4.7489 K6.2269
G2 Z9.3853 X4.2722 I8.5797 K9.0139
G1 Z9.4038 X4.6630
G1 Z10.1399 X4.6630
G3 Z12.3549 X4.5133 I4.1907 K11.2205
G0 Z12.2388 X4.5526
G1 Z13.0489 X4.5526
G1 Z13.0489 X4.1844
G1 Z16.1582 X4.1107
G1 Z24.2084 X4.0969
G1 Z24.2050 X4.4421
G1 Z24.9414 X4.4421
G3 Z26.8192 X4.4790 I4.2652 K25.8841
G1 Z27.6292 X4.4789
G1 Z27.6292 X4.1107
G1 Z27.9733 X4.0905
G1 Z28.0144 X4.0906
G1 Z28.0542 X4.0872
G1 Z28.0928 X4.0805
G1 Z28.1303 X4.0709
G1 Z28.2024 X4.0440
G1 Z28.2712 X4.0086
G1 Z28.6280 X3.7607
G1 Z28.7303 X3.7084
G1 Z28.8024 X3.6846
G1 Z28.8399 X3.6769
G1 Z28.8785 X3.6722
G1 Z28.9184 X3.6710
G1 Z28.9595 X3.6734
G1 Z29.0021 X3.6798
G1 Z29.8658 X3.6779
G1 Z32.5764 X3.5748
G1 Z36.7971 X3.3375
G3 Z37.4152 X3.9149 I3.3172 K37.3948
G3 Z37.9925 X3.2968 I3.3172 K37.3948
G1 Z38.4238 X3.2801
G1 Z39.8890 X3.2257
G1 Z40.4912 X3.1766
G1 Z41.5614 X3.1472
G1 Z47.1804 X2.9795
G3 Z48.9475 X2.9326 I2.7055 K48.0573
G1 Z49.1683 X2.8957
G1 Z49.4629 X2.9325
G1 Z49.7401 X2.9027
G1 Z50.1168 X2.9110
G1 Z51.4429 X2.9010
G1 Z51.7240 X2.9238
G1 Z51.9099 X2.9497
G1 Z52.0945 X2.9858
G1 Z52.1863 X3.0082
G1 Z52.2775 X3.0337
G1 Z52.3684 X3.0625
G1 Z52.4588 X3.0948
G1 Z53.0415 X3.2476
G1 Z54.8026 X3.9313
G1 Z54.8727 X3.9632
G1 Z54.9430 X3.9842
G1 Z55.0133 X3.9954
G1 Z55.0837 X3.9979
G1 Z55.2243 X3.9809
G1 Z55.8058 X3.7656
G1 Z55.8692 X3.4077
G1 Z56.2857 X3.4028
G1 Z56.2698 X2.9038
G1 Z56.9591 X2.8953
G1 Z56.9076 X1.1633
G0 X1.0000
M5M30

Børge

14
General Mach Discussion / Re: Mach3 acting funny
« on: September 23, 2013, 08:33:39 AM »
Hi Ger21, your right, i mixed the versions.
I tried this morning change the IJ mode to INC, it didnt help, same silly picture.....
I rebooted the PC also...


Børge

15
General Mach Discussion / Re: Mach3 acting funny
« on: September 22, 2013, 04:56:56 PM »
What i made was a old style Cannon barrel.
In the newest version that can import .DFX files it looks ok.
In the old version it displays a funny line, with weird arcs in different directions.

Wil check the IJ mode tomorrow, is this the correct window to check it.
Should all settings be the same in both programs in his window.
could it be i altered something yesterday when i ran the motor tuning....

16
General Mach Discussion / Mach3 acting funny
« on: September 22, 2013, 03:39:07 PM »
I import a .DFX file in one version of  Mach3, and make the .TAP file
And open it in a older version it displays the object totally wrong, doesnt look like what i made..
Anyone seen this before.
The file is made in Vectric

Børge

17
General Mach Discussion / Re: Setting the feed speed for the tool
« on: September 17, 2013, 04:02:53 PM »
Hi

I rewrote the code and made it work :)
I did put in the speeds manually, and it worked just fine.
Its doable as long as the code isnt very long.

Børge

Code: [Select]
(File pullert25.tap )
(Monday, September 16, 2013)
G90G80G49G94
G90.1
G0 Z-0.0011 X0.4625
M3
F4.000 G1 Z0.0032 X2.1014
G1 Z3.8912 X2.1055   
G0 Z3.8955 G1 X1.9090 F0.5
F4 G1 Z-0.0011 X1.9090
G0 Z0.0032 G1 X1.7711 F0.5
F4 G1 Z3.8955 X1.7711
G0 Z3.8912 G1 X1.6163 F0.5
F4 G1 Z-0.0052 X1.6163
G0 Z-0.0011 G1 X1.4658 F0.5
F4 G1 Z3.8996 X1.4658
G0 Z3.8996 G1 X1.3320 F0.5
F4 G1 Z-0.0011 X1.3320
G0 Z0.0032 G1 X1.1774 F0.5
F4 G1 Z3.8996 X1.1774
G0 Z3.8996 G1 X1.0478 F0.5
F4 G1 Z-0.0011 X1.0478
G0 Z-0.0011 G1 X0.9140 F0.5
F4 G1 Z0.9989 X0.9140
G0 Z0.9989 G1 X0.7970 F0.5
F4 G1 Z-0.0011 X0.7970
G1 Z0.9989 G1 X0.7050 F0.5
F4 G0 Z0.9989 X0.5963
G1 Z-0.0011 G1 X0.5963 F0.5
F4 G0 Z0.0022 G1 X0.4838
M3
G4 P1 G1 Z-0.0011 G1 X-0.0181
G0 Z0.0022 G1 X0.4838 F0.5
F14 G4 P1 G1 Z0.9989 X0.4838
G1 Z0.9989 G1 X0.9182 F0.5
F14 G1 Z3.8996 X0.9182
G1 Z3.8996 G1 X2.1117 F0.5
G4 P1 G1 Z5.6656 X2.1117
(G0 X1.0000)
M5M30

18
General Mach Discussion / Re: Setting the feed speed for the tool
« on: September 17, 2013, 12:12:04 PM »
Hi Hood

Its a miniature lathe, it doesnt have spindle speed feedback...
I am using metric.

Does this mean it wont work...

Børge

19
General Mach Discussion / Re: Setting the feed speed for the tool
« on: September 16, 2013, 06:14:29 PM »
Thanks Hood
Its a lathe.
If i got it right i will type: G1 X100 F0.25

Børge

20
General Mach Discussion / Setting the feed speed for the tool
« on: September 16, 2013, 04:41:47 PM »
Hi

When turning in metal i would llike the tool to not move so fast against the workpiece.
how do i set this speed.

Børge

Pages: « 1 2 3 »