Messages

1

General Mach Discussion / Re: Copycat plugin to "teach" more than 3 axis possible ?

« on: October 07, 2020, 01:30:21 PM »

I still need help about this problem - thank you

2

General Mach Discussion / Re: Copycat plugin to "teach" more than 3 axis possible ?

« on: October 05, 2020, 03:56:29 PM »

You can load the copycat screen and remove the Rem( ' ) out of each buttons VB code for A & B axis.

hello thank you - where can I find the VB script for copycat ?

3

General Mach Discussion / Copycat plugin to "teach" more than 3 axis possible ?

« on: October 04, 2020, 12:36:31 PM »

hello dear forum,

for an application I need to "teach in" koordinates of 5 axis into G-code file

however copy cat plugin teaches ony 3 axis ?

what can I do ?

thank you

4

Brains Development / is there a way to set / reset an output in brains ?

« on: December 05, 2019, 06:52:40 AM »

hello dear forum,

I want to set / reset an output within brains

how do I do it ?

thank you

5

Brains Development / Re: is there a way to access puls counts of axes from within brains

« on: September 01, 2019, 06:17:40 PM »

first of all I wont use MODBUS RTU
I want use MODBUS TCP
second I want make my own controller in order to earn money
I dont want to write my own MODBUS TCP stack
I want use the one of MACH3
thats why I am asking if it is posible to access
step pulses from within Brains
it will make my development job easy
without necessary to write a plugin for my own board

6

Brains Development / is there a way to access puls counts of axes from within brains

« on: August 27, 2019, 03:19:50 PM »

hello dear forum,

I want access the pulse counts of XYZ axes from within brains in MACH3

what are the relative names of the variables of pulse counts of each axes ?

for example the 10 successive pulse counts of X axes every 1/10 second
( assuming MACH3 updates 10 successive puls counts every 1/ 10 sec )

I want send this pulse counts to MODBUS TCP for own made motion card
to drive step motors 

thank you

7

General Mach Discussion / how to access puls info of axes from within brains

« on: August 25, 2019, 03:56:19 PM »

hello dear forum,

I want access the pulse counts of XYZ axes from within brains in MACH3

what are the relative names of the variables of pulse counts of each axes ?

for example the 10 successive pulse counts of X axes every 1/10 second

thank you

8

General Mach Discussion / has anyone used this paralel port board ?

« on: October 04, 2018, 11:10:35 AM »

hello dear forum,

I want to use this board for paralel port



I want to ask if anyone used this board before ?

can I use the limit switch inputs for homeing axes ?

the board is a product of stepperonline

thank you

9

Mach SDK plugin questions and answers. / Re: shall I download VC++ 2008 x86 or x64 version ?

« on: September 15, 2018, 03:08:31 PM »

hello again ,

now I need to download "Mach plugin wizard"

please the link becouse I couldnot find it anywhere ( if available for win10 )

thank you

10

Mach SDK plugin questions and answers. / Re: shall I download VC++ 2008 x86 or x64 version ?

« on: September 12, 2018, 10:24:43 AM »

thank you

when I mounted the ISO file it didnot need to burn DVD and I could install from mounted ISO file