Messages

691

LazyTurn / Re: LazyTurn

« on: April 19, 2010, 11:06:53 PM »

Rich:

 The error I got indicated a line of length .00000000000000127 in length.Thisline was hosing the load so I assumed it was a 3d issue.
When I got rid of that error, it loaded but cut the finish on the wrong side.. Weird file in some way..

Art

692

LazyTurn / Re: LazyTurn

« on: April 19, 2010, 10:45:22 AM »

Hi:

  3d IS a problem, the file must be in 2d.. but other than that the error is one of a secondary dll I use for spinning and creating the main offsets that sometimes has trouble determining inside from outside. Im looking into it, but it seems the profile ending on or behind zero can cause this as well..

Art

693

LazyTurn / Re: LazyTurn

« on: April 08, 2010, 09:10:15 AM »

HI:

 Yes, I do seem to recall the problem is actually that notepad isntallowed access to read the file.. Hard to say with so many crazy securities built in these days...

Art

694

LazyTurn / Re: LazyTurn

« on: April 07, 2010, 10:32:46 AM »

Kerry:

  Make sure the folder your saving it to has appropriate priviledges. OR, rigth click and run in administrator mode.
I tend to save to desktop, so I dont get that problem, but it shoudlnt appear if the folder your trying to save to
has the write priveleges enabled.. ( Win7 is bad that way..)

Art

695

LazyTurn / Re: LazyTurn

« on: April 01, 2010, 09:50:53 AM »

Rich:

 Ill still see what I can get done before I get swamped with summer work..

As to the profile, Im still a bit flumoxed over its value. Since it pretty much guarentees
gouging as just the true profile, Im curious as to how it could be used. But Ill see if I can at least
make a button that puts out just the profile itself before any tool collision modifications if you feel
it woudl be usefull.. mind you that woudl simply be an offset profile of the actual loaded dxf...only in Gcode..

Art

696

LazyTurn / Re: LazyTurn

« on: April 01, 2010, 09:28:04 AM »

Hi Rich:

   Im not having much luck in enhancements, and my time has pretty much run out for this winters run.
The swapping of point data to arcs is turning out to be very hard to do on many instances of dxf's.
Ill still work on it in spare time when I can till next season, but Im unsure if youll see any more releases this year.


Art

697

General Mach Discussion / Re: Error triggered Art code: 1

« on: March 29, 2010, 06:48:41 PM »

Hi:

  Im afraid it works fine here.. Mach3mill.xml does anyway.

I notice you have a file with no name ".xml" , delete that file and any xml's you dont use and see if that helps..

Art

698

General Mach Discussion / Re: Error triggered Art code: 1

« on: March 29, 2010, 09:56:51 AM »

Hi:

  Hmm, zip the xml profile and post it here and Ill see if I can find the problem, must be a setting somewhere..

Art

699

General Mach Discussion / Re: Error triggered Art code: 1

« on: March 28, 2010, 05:50:20 PM »

Hi:

 Does it happen with Mach3Turn? Or how about trying a new blank profile?

Art

700

Tempest Trajectory Planner / Re: Tempest Planning - Preliminary information and testing

« on: March 26, 2010, 11:05:02 AM »

Hi Mike:

  It woudl give a smoother finish..


By the way, the DSPmc supports SCurve natively because Tempest sends the data in 1ms trajectories, so
when running tempest, any device, printer port, G100, SS etc.. are all supporting SCurve, since its Tempest
that is supplying the information on position.

Art