Messages

171

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: October 13, 2015, 07:28:39 AM »

Hi:

   Your spec doesnt sound too slow. Does the pulse diagnostic show strange variations? Ids the blue line in center really wide?

It may be your motor drivers require wider pulses than Mach3 puts out by default, did you increase the puilse width in the settings?

Art

172

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 09:14:24 PM »

Hi Sasha:

   Cant repeat it with latest versions.. all seems to work fine. You may want to delete the profile and reset tup to see if it makes any dfference, sounds liek a setting is stuck somewhere, but
I cant imagine what. Does the error log show no other message than out of bounds?

Art

173

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 05:36:44 PM »

Hi Sasha :

 Ill install latest versions to see if it helps.
Art

174

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 11:48:52 AM »

Just rebooted to XP and tried with my current builds.. Works fine, no errors. Make sure you have no other axis turned on.. Id turn on only 1 at a time and see if youi can track it down that way.

For the record, my test version was

Darwin reported 1.2646 , config shows 1.22/1.23 and Mach version 1.2646 as well.

Art

175

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 11:34:35 AM »

Ill run a test on mine to see what it does..

176

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 10:13:05 AM »

so 2178 is working ok,  "1.2472" of the Darwin Plugin is not?  Try the attached file, any difference?

Art
 

177

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 07, 2015, 08:59:08 AM »

Sasha:

 That error should only come out if the speed is wriong, it happens only if the driver tries to go faster than it can, so if its set to 30K, if it tries to go 31K..

Are your pulse settings agreeing with your max velocities?

Art

178

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: September 05, 2015, 08:11:26 AM »

No problem Tom,

  I monitor this thread so whenever you get testing, I should be here to help. I will be away Oct 1 for a couple weeks
, but will answer when I get back should you be testing then.

Art

179

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 31, 2015, 10:13:06 PM »

The license issue is really pinging my memory though, make sure its not just the license in latest version..

Art

180

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: August 31, 2015, 09:11:34 PM »

Hi Tom:

  Interesting finding. I will try homing tomorrow in 2611 and see what mine does.. It sounds like somethign changed..

 ( hmm, did you check to see if your license works with the later version of Mach4? Does is show Darwin as licensed? If not, the homing wouldnt work,
and I did hear of some licenseing issues where you needed to get a new license on latest version..

Art