Messages

1361

Video P*r*o*b*i*n*g / First Mesh

« on: December 08, 2007, 12:04:08 PM »

Hi Guys:

  This is the unreleased MachClouds first mesh, before postprocessing to clean it up.. Still lots to do, but
its looking not too bad.

Art

1362

Video P*r*o*b*i*n*g / Re: Driver Installation question

« on: December 07, 2007, 11:23:56 AM »

Same as LCam, center mouse button to rotate, shift and ctrl to pan and zoom..

Art

1363

General Mach Discussion / Re: Help!!!! Mach gone crazy

« on: December 07, 2007, 10:35:08 AM »

save your mach2mill.xml and reinstall.. then copy it back.. Sounds liek it may be the xml thats the trouble though. Id check all the motor tuning and retune myself.. seomthignis very screwed up..

Art

1364

Video P*r*o*b*i*n*g / Re: Driver Installation question

« on: December 07, 2007, 09:03:46 AM »

Don:

 Leave the XStep at 1, just set the X scan at 0..

Art

1365

General Mach Discussion / Re: Help!!!! Mach gone crazy

« on: December 06, 2007, 11:52:56 PM »

It sounds to me like one day you were at 35Khz or 40Khz, then somethign happened and it went back to 25Khz..

Id check that and jump up to 35 or 45 if thats where you tuned the motors.. seomthing doesnt sound rigth though.. I cant figure why your at 6 all the time, thats not FRO that goes to 6, thats just the feedrate commanded display. FRO should be at 100%.

  SO try this, type F1 in the MDI line, then on the main page, does the feedrate read 1?

If you type 1 where the feedrate display is and hit enter,  does it change to 1?

What ahppens in the program now?

Art

1366

Video P*r*o*b*i*n*g / Re: Driver Installation question

« on: December 06, 2007, 10:53:07 PM »

Don:
 If the laser line is in the X direction, then leave X at 0, set Y to the range of the scan.. 4 or 5 inches, and just hit scan..

The pointcloud will show up in the mach3 folder..

Art

(I recommend only scanning in the Y direction right now, unless the laser from right to left is in the Y direction.. )

1367

Video P*r*o*b*i*n*g / Re: Driver Installation question

« on: December 05, 2007, 09:05:28 AM »

Dave:

 The white line in raw data, the red is processed data.. just debugginmg stuff for me thats all, quite normal..
 There will be an update to make it all make more sense as soon as I finish a bit more on machcloud..
The knob doesnt look too bad. When machcloud is done itll clean it up alot..

Art

1368

Video P*r*o*b*i*n*g / Re: MachCloud point viewer program

« on: December 03, 2007, 09:56:09 PM »

Tom:

  Hmm, not a bad idea at all.. Im still working on th eviewer, but I have some things I want to add in
the point cloud maker as well, so Ill add that when I get there. Probably some interesting things one could do with such data..

Art

1369

Video P*r*o*b*i*n*g / Re: Driver Installation question

« on: December 03, 2007, 09:16:51 AM »

Hi:

 Just select config/general, and turn off "Use Watchdogs" , thatll cure it..

Art

1370

Video P*r*o*b*i*n*g / Re: Driver Installation question

« on: December 01, 2007, 03:13:20 PM »

Yup, thats how it works..

Art