Hello Guest it is September 21, 2023, 02:41:19 PM
Profile Guest

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Pysiek

Pages: 1 2 3 4 »
1
Finished Screens / Re: Mach3 2010 Screenset - Now available
« on: October 31, 2013, 10:04:31 AM »
Hello
I have purchase the screenset couple days ago. I run the installation file and start Mach3. When I try to load the screenset it shows "bitmap goes here" and it loads like only 5% of the graphics. Basically its not usable because nothing is on the screen.

2
General Mach Discussion / Re: Re: Newbie with KL-4030 1st time testing problems
« on: April 01, 2013, 07:16:55 AM »
I will try that later after work.

3
General Mach Discussion / Re: Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 06:22:01 PM »
That's where I connect the master switch as per wiring diagram. But when I disconnect it it still moving the motors

4
General Mach Discussion / Re: Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 05:50:32 PM »
No. Estop is set up on different input.

5
General Mach Discussion / Re: Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 05:28:41 PM »
The only weird thing it is right now that no matter if I press the master switch or leave it unpressed everything works fine. I thought if I release the master switch then nothing will work

6
General Mach Discussion / Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 05:26:08 PM »
I got it!!!!!!!!!!!!!!!!!!!!!!  ;D
Followed these :
Quote
Rather, I'd suggest you check if it's communicating by bringing up mach and hitting the diagnostics screen. In there you can see all the port pins and if you short any of the 5 inputs to ground it should blink on and off as you do it. For example, take a pair of wires and connect to pin 13 and ground, touch them together and see if it lights up in mach. If it does, that's a clue that you are communicating with the port / cable / card.
From here: http://www.buildyourtools.com/forums/index.php?f=9&t=818&rb_v=viewtopic

And the problem was one of the jumpers on the breakout board. It have to be switched to be connected between 2-3 which mean COM=5V . Before it was connected between 1-2 which mean COM=GND

7
General Mach Discussion / Re: Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 04:52:50 PM »
Nope. Didn't work

8
General Mach Discussion / Re: Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 02:36:48 PM »
Okay. I'm going to do some work or my wife gonna put me in the basement. We will see what Keling Inc replies to me

9
General Mach Discussion / Re: Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 02:14:59 PM »
One more thing. Is it possible that I have damaged the driver if I connect power and all the switches on the driver where in ON position(down)?

10
General Mach Discussion / Re: Newbie with KL-4030 1st time testing problems
« on: March 29, 2013, 02:11:13 PM »
Quote from: Chaoticone on March 29, 2013, 02:09:21 PM
Tweakie, I'm guessing those en pins are enable do you know?

Brett
In the manual it says that if those are left unconnected then the driver is enabled . http://www.kelinginc.net/KL-4030.pdf

Pages: 1 2 3 4 »