Messages

81

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 07:51:05 PM »

Very Nice!! thanks you so much!!! there is no pause at all
Is it because you used only one Gcode comand as in G1?
what dose the F100000.0 represent?
 
YOU THE MAN BARKER!!

82

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 12:34:01 PM »

Got it!! P1 Is output 3 P2 is output 4 and so on,,
Thanks,, Those M10 and M11 comands are going to come in handy,,

83

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 10:40:29 AM »

still not turning it on, I set output #1 to pin 14 ( thats what output pin im on not 16)  ran it just like you have it

M3   
M11 P1
G0 X-05.000 Y00.00000 Z00.00000
G0 X-08.000 Y00.00000 Z00.00000
M10 P1
G0 X 00.000 Y00.00000 Z00.00000
M30

I am running Mach 3, I  dont see in the M codes an M11 and M10,, Im quesing M11 on and M10 off

84

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 10:17:35 AM »

sorry still thinking
p means output pin # Im on pin 16 so I would put P16

85

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 10:14:59 AM »

I mean output #1

86

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 10:12:51 AM »

I ran that there was no pause but it didnt turn on my relay,, P1? is that pump 1, input 1?

87

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 09:33:37 AM »

Thanks for the intrest Brian,,
I Built and Induction Heat Treat Scanner run by stepper motors,, Im sure the programing looks like childs play to you.
M3 turns on a dc motor that spins the part, M7 turns my induction heater on, and M9 turn the induction heater off, but what is happening is there is a momentary puse right when it shut my induction heater off,, witch really is not a big deal but the heated steel needs to get into the quench as quicky as posible,  to become harden.
thanks
josh


M3
M7
G0 X-05.000 Y00.00000 Z00.00000
G0 X-08.000 Y00.00000 Z00.00000M9
G0 X 00.000 Y00.00000 Z00.00000
M30

88

General Mach Discussion / Re: Motors ramp up with each line of g code??

« on: May 18, 2007, 09:12:15 AM »

Thanks for the response
but unless I am putting it in the wrong line, it still pauses between Gcode lines??

89

General Mach Discussion / Motors ramp up with each line of g code??

« on: May 17, 2007, 07:35:29 PM »

Hello,,
I have things up and running, all my hardware problems are solved, now all I need to do is learn how to program g codes.. It seems when your g code starts another line the motors will slow down and ramp up on evey line of g code. If I am already moving in X+ direction during a line of g code and in the next line I am still going in X+ direction is there a way to keep my speed in x+ direction??

Thanks to all
Josh

90

General Mach Discussion / Re: External start button

« on: April 28, 2007, 07:32:30 AM »

Up bright and early in the shop, all is well, works fine!!  I also printed off OEM buttons list from MachCustomize WIKI  Here is the address if anybody else needs any external buttons or switches for there project.  http://www.artsoftcontrols.com/MachCustomizeWiki/index.php?title=OEM_Buttons

Thanks Alot HOOD
Josh