Hello Guest it is September 19, 2021, 10:18:09 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Kenneth

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 »
241
Machscreen Screen Designer / Re: User DRO (Counter)
« on: March 04, 2013, 03:19:32 PM »
in the VB editor, it changes the dro with each run.
but if i use m1001 in mdi, nothing.
can someone tell me what i'm missing ?
Thanks

242
Machscreen Screen Designer / Re: User DRO (Counter)
« on: March 04, 2013, 02:25:32 PM »
i wrote this(with a lot of reading)don't think it's posssible from what i read.
it works in the VB editor. but not in Mach3.
do i use M1001 in the MDI ?

file name = C:\Mach3\macros\MyMill\M1001.m1s
Count = GetUserDRO(1010)
Count = GetUserDRO(1010)+1
While IsMoving
Wend
SetUserDRO(1010 , Count)   

243
Machscreen Screen Designer / Re: User DRO (Counter)
« on: March 04, 2013, 12:18:20 PM »
can someone at least let me know if this is possible ?
brain....script .... voodoo ?

Thanks :)

244
Machscreen Screen Designer / User DRO (Counter)
« on: March 04, 2013, 09:46:17 AM »
i usually cut pockets and i woud like a userdro to count each time Z move to the
next depth to cut the pocket. ex.  g1 f4 z-.1 DRO 1...g1 f4 z-.2 DRO 2 ....etc.
but not count just because Z moves. is this possible and do i use a brain ?
Thanks for any help !

245
General Mach Discussion / Re: Sherline w/Mach 3
« on: February 26, 2013, 02:20:07 PM »
Picture of what i have for the sherline mill(5400)


Thanks Hood

246
General Mach Discussion / Re: Sherline w/Mach 3
« on: February 26, 2013, 10:02:20 AM »
tried to attach a pic but it said it was already attached.

P.S. will (try) to look at dates :)

247
General Mach Discussion / Re: Sherline w/Mach 3
« on: February 26, 2013, 06:40:53 AM »
new to mach3 but also have sherline mill(5400)
check dir/step pins.

Kenneth

(D###, really need to look at dates)


248
Mach Screens / Re: labels incorrect in mach3
« on: February 26, 2013, 05:58:18 AM »
when i use the "auto enlage screen" i get what you said Brett.
just don't know how to remove the extras in machscreen.
even enlarging the frame doesn't show anything.


Kenneth

249
Mach Screens / Re: labels incorrect in mach3
« on: February 26, 2013, 05:41:15 AM »
i emailed the file Klaus

250
Mach Screens / Re: labels incorrect in mach3
« on: February 25, 2013, 10:15:15 AM »
Thanks Chaoticone

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 »